667030

Celestron CPC Deluxe 800 HD - 11007 Manual

8
Zoom out
Zoom in
Previous page
1/50
Next page
6
>> www.celestron.com
The Eyepiece
The eyepiece is the optical element that magnies the image focused by
the telescope. The eyepiece ts into either the visual back directly or the
star diagonal. To install the eyepiece:
1. Loosen the thumbscrew on the star diagonal so it does not obstruct
the inner diameter of the eyepiece end of the diagonal.
2. Slide the chrome portion of the eyepiece into the star diagonal.
3. Tighten the thumbscrew to hold the eyepiece in place.
To remove the eyepiece, loosen the thumbscrew on the star diagonal
and slide the eyepiece out.
Eyepieces are commonly referred to by focal length and barrel diameter.
The focal length of each eyepiece is printed on the eyepiece barrel.
The longer the focal length (i.e., the larger the number) the lower the
eyepiece power or magnication; and the shorter the focal length
(i.e., the smaller the number) the higher the magnication. Generally,
you will use low-to-moderate power when viewing. For more information
on how to determine power, see the section on “Calculating Magnication.”
Barrel diameter is the diameter of the barrel that slides into the star
diagonal or visual back. The CPC uses eyepieces with a standard 1-1/4”
barrel diameter.






The Finderscope
The CPC telescope comes with a 9x50 nderscope. The specications
for a nderscope stand for the magnication and the aperture, in
millimeters, of the scope. So, a 9x50 nder magnies objects nine times
and has a 50 mm objective lens.
Finderscope Installation
The nderscope must rst be mounted in the included quick-release
bracket then attached to the rear cell of the telescope. To install
the nderscope:
1. Locate the nderscope mounting bracket attached to the bottom
portion of the nder bracket. Loosen the two thumb screws to slide
the mounting bracket from the nderscope bracket.
2. Find the two holes in the rear cell of the telescope on the top left,
when looking from the back of the tube.
3. Place the mounting bracket over the two holes of the rear cell as
shown in the gure 3-7.
4. Insert the screws through the bracket and into the rear cell.
WARNING: If you remove the mounting bracket, do not
completely thread the screws back into the rear cell of the
telescope. The screws may be long enough to obstruct the
movement of, and possibly damage the primary mirror.




With the bracket rmly attached to the telescope, you are ready to
attach the nder to the bracket.
1. Slide the O-Ring over the back of the nderscope and position it on
the tube toward the objective end of the nderscope.
2. Slide the eyepiece end of the nderscope into the front ring of the
bracket (the front ring is the one without the adjustment screws),
then through the back ring. It may be necessary to push down the
spring loaded pivot screw so that the nder will pass through the back
ring (see gure 3-6).
3. Push the nder back until the O-Ring is snug inside the front ring of
the nder bracket.
4. Hand tighten the two adjustment thumb screws until they make
contact with the nderscope.








… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Celestron CPC Deluxe 800 HD - 11007 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Celestron CPC Deluxe 800 HD - 11007 in the language / languages: English as an attachment in your email.

The manual is 10,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info