667043
9
Zoom out
Zoom in
Previous page
1/36
Next page
I 9
2. Remove the counterweight safety screw on the bottom
end of the counterweight bar by turning it counterclock-
wise. This screw prevents the counterweight from falling
off the mount in the case the counterweight locking screw
comes loose.
3. Loosen the locking screw on the side of the counter-
weight.
4. Slide the counterweight over the counterweight bar and
move it about halfway up the bar.
5. Tighten the locking screw on the side of the counter-
weight to hold it in place.
6. Replace the counterweight safety screw.
Tip: The hole in the center of your counterweight is slightly
larger on one side. When you slide the counterweight
onto the counterweight bar, make sure that the smaller
hole is facing the equatorial head. This allows you to
slide the counterweight over the safety screw at the
bottom of the counterweight bar in case you need a
little bit more adjustment to balance additional acces-
sories mounted on your optical tube. The smaller hole
prevents the counterweight from completely sliding
over the safety screw.
Attaching the Hand Control Holder
The Advanced VX telescope models come with a hand
control holder that attaches to a tripod leg. The hand control
holder comes in two pieces: the Leg Clamp that snaps
around the tripod leg and the holder which attaches to the
Leg Clamp. To attach the hand control holder:
1. Place the leg clamp up against one of the tripod legs
and press firmly until the clamp wraps around the leg.
2. Slide the back of the hand control holder downward into
the channel on the front of the legs clamp until it snaps
into place.
Attaching an Optical Tube to the Mount
The telescope attaches to the mount via a dovetail slide
bar which is mounted along the bottom of the telescope
tube. Before you attach the optical tube, make sure that the
declination and right ascension clutch knobs are tight and
the counterweight(s) are securely installed. This will ensure
that the mount does not move suddenly while attaching the
telescope. To mount the telescope tube:
1. Loosen the two mounting screws on the side of the
telescope mounting platform. This allows you to slide
the dovetail bar onto the mount.
2. If your telescope is equipped with one, remove the safety
screws located beneath the dovetail bar.
3. Slide the dovetail bar on the telescope tube into the
mounting platform of the mount. Slide the telescope so
that the back of the dovetail bar is close to the back of
the mounting platform.
4. Tighten the mounting screws on the side of the mounting
platform to hold the telescope in place.
Now that the optical tube is securely in place, the visual
accessories can now be attached to the telescope. This is
covered in detail in the section of this manual dealing with
the use of optical tubes.
Moving the Telescope Manually
In order to properly balance your telescope, you will need to
move your telescope manually at various portions of the sky
to observe different objects. To make rough adjustments,
loosen the R.A. and DEC clutch knobs slightly and move
the telescope in the desired direction.
Both the R.A. and DEC axis have lock levers to clutch down
each axis of the telescope. To loosen the clutches on the
telescope, rotate the lock levers counterclockwise.
Safety
Screw
Dovetail Bar
Telescope
Mounting
Screw
Hand Control Holder
Leg Clamp
Declination
Clutch Lever
RA Clutch
Lever
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Celestron Advanced VX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Celestron Advanced VX in the language / languages: English as an attachment in your email.

The manual is 5,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Celestron Advanced VX

Celestron Advanced VX User Manual - German - 36 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info