791750

Celestron 47005 Manual

3
Zoom out
Zoom in
Previous page
1/15
Next page
The pressure history bar displays the moving atmospheric pressure history of the past 12 hours
which allows for forecasting. To view air pressure history for the past 12 hours, press the “hist”
button to select and view how many hours (repeatedly press the “hist” button).
The respective values can only be available after the barometer recorded the pressure date in the
past 12 hours. The spectrum bar chart indicates pressure changes of the past 1, 2, 3, 6, and 12
hours and is shown for a range of -0.24 to +0.24 in/Hg and -8 to +8 mb/hPa.
y Temperature & Humidity Alert – press the “alert” button on the rear of the Receiver to turn
the alert on or off. Press and hold the “alert” button to enter the setup mode. The indoor and
outdoor temperature and humidity upper and lower limits can be set by using the “+” and “-”
buttons and pressing “alert” to confirm each setting. When either the temperature or humidity
alert values have been reached while the alert is activated, the respective values will flash and
the alarm will sound --press “alert” to stop the alarm.
y Alarm Setting – Press the “alarm” button to toggle between alarm 1 and alarm 2, and normal
time. In “alarm 1” or “alarm 2” press and hold to set the alarm time by using the “+” and “-”
buttons to set the hour and minute and press the “alarm” button to confirm each. To turn either
alarm on or off, toggle the “+” button and you will see a bell icon for alarm 1 or alarm 2 or both
or none.
y Snooze/Light – when the alarm goes off, press the “snooze” button to go into snooze mode and
the alarm will go off again after 9 minutes and then continue to do this every 9 minutes. To stop
the snooze, press the “alarm” button. To enable the backlight for a moment just push the
“snooze/light” button in normal mode and for having the light on for a longer time keep holding
down the button.
y Channel – if your Sensor is set correctly to Channel 1, then a small icon to the left of outdoor
temperature display will show a “1” in a box. If you do not have an outdoor temperature and
humidity display, make sure that the “1” is displayed and if not (shows a 2 or 3), then push the
“CH” button until it shows the “1”.
Specifications:
y Indoor Temperature Range = 0º to +50º C (+ 32º to + 122º F)
y Remote Sensor Temperature Range = -20º to + 60º C (-4º to + 140º F)
y Indoor/Outdoor Humidity Range = 20% to 95% Relative Humidity
y Resolution = ± .5º C (± 1.5º F) for temperature & ± 1.5% humidity
y Altimeter = 328 ft to 8202 ft (100 m to 2500 m)
y Barometer = 26.80 to 31.01 in/Hg (900 to 1050 mb/hPa)
y Clock = digital quartz
y Transmission = RF433 MHz
y Dimensions = Receiver – 4.0” x 1.0” x 10.0” (102mmx25mmx254mm) Sensor - 2.5” x 1.0” x
3.6” (63mm x 25mm x 91 mm)
y Weight = Receiver - 14oz/397g Sensor - 3oz/85g
2835 Columbia St.
Torrance, California 90503 U.S.A.
www.celestron.com
Printed in China 0110 RoHS
3 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Celestron 47005 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Celestron 47005 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 0.64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info