753590

Cecotec Conga Windroid 980 connected Manual

7
Zoom out
Zoom in
Previous page
1/15
Next page
980 CONNECTED 4544
ENGLISH ENGLISH
Fig. 15.
Stop:
When cleaning is over, the product returns to the place where cleaning started and beeps.
Remove the robot from the surface
Fig. 16.
Grab the handle and press Start/Pause for more than 5 seconds. Then, remove the product.
Turn the robot off
Fig. 17.
Move the switch button to the “O” position.
Remove the safety suction pad
Fig. 18.
Unplug the product from the power supply.
Fig. 19.
Note: when the product displays a red light and beeps, please check if the power adapter is
connected correctly. When the power adapter is correctly connected, the product will show
a blue light and will start operating. When the power adapter is connected correctly, and
the product still shows a red light, please use the direction buttons on the remote control to
operate the product and move it from its current position, until the blue light shows up, press
Start/Pause keys on the remote control for the product to operate properly.
4. CLEANING AND MAINTENANCE
When cleaning the mop cloth and the bottom parts of the product, please switch off the
product.
Clean mop cloth
Turn the robot over and remove the mop cloth, soak it in cool, clean water for 2 minutes.
Handwash with mild detergent and lay flat to dry. Let it dry completely before attaching it
again to the robot.
Do not use a wet mop cloth on the robot or it may slip on the window.
Washing the mop cloth regularly can extend its service life.
If the cloth becomes worn or no longer fits, replace it with a new one to achieve best cleaning
performance.
Fig. 20.
Fan cleaning
Turn the robot over and wipe any debris from the fan with a cloth to maintain suction.
Guide wheels cleaning
Turn the robot over and wipe the four side rollers with a cloth to maintain their effectiveness.
Edge Detection Sensors cleaning
Turn over the robot and wipe five edge detection sensors clean with a cloth to maintain their
effectiveness.
Fig. 21.
Squeegees cleaning
Turn over the robot and wipe five edge detection sensors clean with a cloth to maintain their
effectiveness.
Driving wheels cleaning
Before cleaning the wheels, move the power switch to the “-” position. Then wait 8 seconds
until it stops vacuuming and starts beeping. Then press the Start/Pause button key on the
remote control and start cleaning the driving wheels.
Fig. 22.
Press Start/Pause and Clean buttons on the remote control to check the driving wheels. If
there is any dust, press pause and clean the dust.
Fig. 23.
After cleaning, turn off the switch on of the bottom part to the “O” position.
Light status indicator
Blue light
flashing
The product can be placed on the glass.
Steady blue
light
Product suction is succesful. The robot remains attached to window and it
can start cleaning the window.
Red light
flashing
The robot stops suctioning so it can be removed from the window.
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cecotec Conga Windroid 980 connected at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cecotec Conga Windroid 980 connected in the language / languages: English as an attachment in your email.

The manual is 1,83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info