Manual Cata DUCT IN LINE 150 (page 9 of 30) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian)

741067

Zoom out

Zoom in

1/30

It can be disconnected by making the plug accessible or by in-

corporating a switch in the fixed wiring that meets electrical ins-

tallation standards.

The appliance must be permanently connected with wiring for

fixed installation.

(2- or 3-core cable with a minimum cross-section of 1 mm2 and

maximum of 1.5 mm2).

To complete the electrical connection, follow the wiring diagram

depending on the model that you wish to connect (see fig. 3A,

3B, 4A, 4B).

No earthing connection is required, given that this is a doubly-

insulated appliance (Class II).

Remove the connection cover as shown in fig. 2.

Perforate the flex holder (O) to allow the power supply wires to

pass through.

The power supply cable must be placed so that no liquid or va-

pour can enter the appliance along it. If this were not possible, the

cable entry should be sealed additionally,

e.g. with silicone. Otherwise, the indicated IP rating would not

be maintained.

This appliance has a one, two or three-speed motor (depending

on the model)

If you wish to install a commutator that lets you choose between

high speed (S3), medium speed (S2) (only in the Duct in Line

200/910 model) and slow speed (S1), see fig. 3A - 3B.

The timer is factory set only for high speed (S2).

If you wish, you can set the timer for low speed (S1) leaving the

high speed (S2) without a timer

• Connect the cable corresponding to the speed that you wish

to time to the Motor Line terminal on the electronic Timer panel.

• Connect the cable corresponding to the other speed to the gene-

ral power strip (TB) for operation without the timer.

Available versions:

• STANDARD. Does not require setting

• TIMER. Adjustable timer from 3’ to 15’.

In the event that this appliance is not used, it is recommended

that you disconnect it from the mains electricity supply.

SETTINGS AND OPERATION:

Perform the necessary settings according to the model installed.

TIMER (see fig. 4A - 4B)

To set the timer, turn the TIMER pin clockwise to increase the

time (3’- 15’).

The extractor fan will start, activated by the switch. When the

switch is deactivated,

the fan continues working for the set time and then turns off.

To finish the installation, verify that all the connections have been

done correctly

and make sure that the cables are placed correctly.

Place the connection cover in the correct position again and en-

sure that it cannot be removed without using a tool.

Make sure that the blades turn freely.

CLEANING AND MAINTENANCE:

• Before cleaning make sure that the appliance is not connected

to the electric network

and prevent it from being reconnected by accident.

• Clean with a damp cloth regularly.

• For maintenance operations

• The casing assembly must be removed from its position (see

fig. 2)

• Remove the two reducer pipes (V): Loosen the screws on the re-

ducer pipes, turn each reducer pipe about 9º in an anti-clockwise

direction and remove the pipe by pulling it (see fig. 5).

• The motor, propeller and all components should be inspected

periodically to ensure that they are not dirty and have not suffe-

red any damage. The frequency of inspections depends on the

appliance’s operating conditions.

• Remove the dirt on the propeller and the inner parts of the ca-

sing to avoid imbalances during operation, a decrease in aerody-

namic performance and motor damage.

• Motor bearings do not need maintenance.

• Once maintenance is complete, refit the reducer pipes and ca-

sing assembly.

Always demand original spare parts for repairs.

THE MANUFACTURER reserves the right to make any tech-

nological improvement or modification without prior notifi-

cation.

The symbol on the product or on its packaging indicates that

this product may not be treated as household waste. Instead it

shall be handed over to the applicable collection point for the re-

cycling of electrical and electronic equipment. By ensuring this

product is disposed of correctly, you will help prevent potential

negative consequences for the environment and human health,

which could otherwise be caused by inappropriate waste handling

of this product. For more detailed information about recycling of

this product, please contact your local city office, your household

waste disposal service or the shop where you purchased the pro-

duct.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Cata DUCT IN LINE 150 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian as an attachment in your email.

The manual is 2,98 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Cata DUCT IN LINE 150 Manual

Product: