467053

Casio KL-120 Manual

9
Zoom out
Zoom in
Previous page
1/48
Next page
E-25
Tape cartridge
compartment cover is not
closed completely.
No more tape left in the
cartridge.
Tape jam
Securely close the cover.
Replace the tape cartridge with a
new one.
Remove the tape cartridge and pull
out the jammed tape by hand. Cut off
excess tape with scissors, and
carefully replace the cartridge into
the label printer.
Important!
Never allow the tape outlet to
become blocked and never touch
tape as it is being fed during printing.
Tape does not come out when PRINT is pressed.
Possible Causes Action Page
E-9
E-9
E-9
Printing is blurred, blotched, broken, etc.
Possible Causes Action Page
Improper print density
setting
Improper loading of the
cartridge
Dirty printer head or
rubber roller
Adjust the print density setting.
Remove the tape cartridge and
reload it correctly.
Clean the printer head and roller.
E-22
E-9
E-23
Tape comes out when PRINT is pressed, but nothing is printed on it.
Possible Causes Action Page
Only blank spaces were
input.
Input the text you want to print.
E-10
••
••
•
Printing
Remove the tape cartridge and check
to make sure the ink ribbon is not
broken. Next, take up any slack in the
ink ribbon and then reload the tape
cartridge.
Important!
• Before loading a tape cartridge into
the label printer, always make sure
you take up any slack in the ink
ribbon first.
• If the ink ribbon is broken, you
must change to another tape
cartridge.
Tape cartridge loaded
while the ink ribbon is
slack.
Ink ribbon is being fed from the tape outlet along with the tape.
Possible Causes Action Page
E-9
Load a fresh set of AA-size alkaline
batteries (supplied by you).
Battery power is low or
the wrong type of
batteries are loaded in
the printer.
Printer powers down while printing is in progress.
Possible Causes Action Page
E-8
E-27
Message
DATA ERROR!
NO INPUT TEXT!
PRINT ERROR!
TOO MANY
CHARACTERS!
Possible Causes
• Data in memory has
become corrupted for
some reason.
• You are attempting a print
or preview operation
when no text are input.
• The tape became jammed
during printing.
• You are attempting to
input more than
80 characters into text.
• The number of characters
you are trying to input
while using Layout
Prinitng exceeds the
maximum number of
allowable characters.
Action
• Press any key besides
ON/OFF to clear the
error message. In
response to the
“INITIALIZE THE
PRINTER!” message
that appears, press any
key besides ON/OFF to
initialize the Label
Printer.
• Input the text and then
try again.
• Turn off the printer and
remove the tape
cartridge. Next, remove
the jammed tape.
* If the steps described
above do not clear the
error message, contact
your retailer or your
nearest CASIO service
center.
• Reduce the number of
characters in the
sentence.
Message
TOO MANY
BLOCKS!
LOAD A TAPE
12mm OR
WIDER
CLRS TAPE
LNGTH
SET/ESC
Possible Causes
• You are attempting to
input more than two block
marks (
B
) into text.
• A 6mm or 9mm tape
cartridge was loaded in
the printer while a 2-line
or 2-block format is
selected for Layout
Printing.
• You are attempting to
input a block mark while
FIX is selected for TAPE
LENGTH.
Action
• Use only one or two
block marks (
B
) in a
single sentence.
• Turn off the printer and
replace the tape
cartridge with one that is
12mm or wider.
• If you want to cancel the
TAPE LENGTH setting
and input a block mark,
press SET. If you do not
want to input a block
mark, press ESC.
E-26
••
••
•
Using Labels
Label will not adhere to a surface.
Possible Causes Action Page
Peel the backing paper from the back
of the tape to expose the adhesive.
Labels do not adhere well to surfaces
that are rough, wet, oily, or dirty.
The backing paper is still
on the back of the tape.
Surface is unsuitable for
affixing a tape.
E-18
E-18
Message
TOO MANY
LINES!
NO DATA!
OVERWRITE?
SET/ESC
LOAD A TAPE
CARTRIDGE
* This message
also appears
when the tape
cartridge is
loaded correctly,
but “NONE” is
selected for the
tape width.
LOW BATTERY!
LONGER THAN
SET!
SET/ESC
Possible Causes
• The number carriage
returns you input causes
the label to exceed the
maximum number of lines
for the tape you are
using.
• You are attempting to
recall text from memory
when there is none
stored.
• You are attempting to
store text in memory
when it already contained
text.
• You are attempting to
perform printing without
setting a tape cartridge.
• Battery power is low.
• This message appears
when the length of the
tape that will actually be
printed is longer than the
specified tape length.
Action
• Use wider tape or reduce
the number of lines.
6mm tape...1 line
9mm tape...1 line
12mm tape...Up to 2 lines
18mm tape...Up to 2 lines
• Store the text in memory
and then try again.
• Press SET to overwrite
the existing text with the
new text, or ESC to
cancel the store
operation.
• Turn the power OFF and
set the tape cartridge.
• Replace the batteries.
• To print, press SET.
• To cancel printing, press
ESC. You can then
decrease the number of
characters, change to a
longer tape setting, or
select auto tape length.
Error Messages/Display Messages
Cannot cut tape.
Possible Causes Action Page
Tape cutter blade is dull. Take the label printer to the dealer
from whom you purchased it to have
the tape cutter blade replaced.
—
Printed text is cut off by tape cut operation.
Possible Causes Action Page
Replace the tape cartridge with a new
one.
Out of tape
E-9
••
••
•
Tape Cutting
E-28
Alpha Characters
Symbols
KL-120
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Casio KL-120 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Casio KL-120 in the language / languages: English, German, French, Italian, Swedish, Spanish as an attachment in your email.

The manual is 1,99 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info