480711
160
Zoom out
Zoom in
Previous page
1/167
Next page
49
Command execution example
Only the following 4 patterns can be set. (1) is set as an initial value to each cid.
(1) Command for permitting all speeds of both uplink and downlink (when cid is 5)
AT+CGEQMIN=5
OK
(2) Command for permitting only the speed of uplink 5,760kbps and downlink 7,232kbps (when cid is 6)
AT+CGEQMIN=6,,5760,7232
OK
(3) Command for permitting uplink 5,760kbps and all speeds of downlink (when cid is 7)
AT+CGEQMIN=7,,5760
OK
(4) Command for permitting all speeds of uplink and only 7,232kbps of downlink (when cid is 8)
AT+CGEQMIN=8,,,7232
OK
Command name: +CGEQREQ=[parameter]
Outline
Sets the QoS (quality of service) to be requested to network when originating a PPP packet communication.
For setting, only the following pattern in the command execution example can be set, which is also set as an initial
value.
Though this command is a setting command, it will not be recorded in non-volatile memory written by [&W], nor reset
by [&F] or [Z].
Format
+CGEQREQ=[<cid>]
Explanation of the parameters
<cid>
*
1 to 10
* <cid> is a number for managing the access point name (APN) registered in the FOMA terminal for a packet
communication.
Operation performed when the parameter is omitted
+CGEQREQ=Sets the initial value to all <cid>.
+CGEQREQ=<cid>Sets the specified <cid> to the initial value.
+CGEQREQ=?Displays a list of values that can be set.
+CGEQREQ?Displays the current setting.
Command execution example
Only the following 1 pattern can be set. This is set to each cid as an initial value.
Command for requesting a connection at a speed of uplink 5,760kbps and downlink 7,232kbps (when cid is 5).
AT+CGEQREQ=5
OK
Saving modem port command setting value
The values set by AT commands are initialized every time the power of FOMA terminal is turned on or off, except the
access point name (APN) set by AT+CGDCONT command (p.25), QoS setting by AT+CGEQMIN/AT+CGEQREQ
command, permit or reject incoming call setting by ATDGAPL/ATDGARL/ATDGANSM command, the setting for
specifying sending/not sending caller ID of packet communication set by ATDGPIR command and the setting for
specifying sending/not sending caller ID of 64K data communication set by AT+CLIR command. However, you can save
the values set by commands with [&W] if you enter
    AT&W
after the setting. In this case, other set values with [&W] will also be saved. These values can be retrieved by entering
    ATZ
even after the power is turned on or off.
CA-01C_E_Manual_02.fm 49 ページ 2011年5月3日 火曜日 午後12時30分
160


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Casio CA-01C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Casio CA-01C in the language / languages: English as an attachment in your email.

The manual is 9,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info