624852

Casio 5365 - PRW-6000 Manual

8
Zoom out
Zoom in
Previous page
1/15
Next page
E-56
• The altitude tendency graph shows changes in altitude over the past 6 readings while readings are
being taken automatically.
50 meters
(10 meters for
each block )
6 readings
ago
Current
reading
Using Reference Altitude Values
To minimize the chance of reading error, you should update the reference altitude value before setting off
on a trek or any other activity where you plan to take altitude readings. During a trek, keep checking the
readings produced by the watch against altitude information provided by markers and other information,
and update the reference altitude value as required.
• Reading error can be caused by changes in barometric pressure, atmospheric conditions, and
elevation.
• Before performing the procedure below, look up the altitude of your current location on a map, the
Internet, etc.
E-57
To specify a reference altitude value
1. In the Altimeter Mode, pull out the crown.
• This will cause the current altitude reading value to fl ash on the
digital display.
• The timekeeping (hour, minute, second) hands will move to 2
o’clock.
2. Rotate the crown to change the altitude value in one-meter (fi ve-foot)
increments.
• You can also use HS1 high-speed movement (page E-5) to change
this setting.
• Change the reference altitude value to an accurate altitude reading
that you get from a map or other source.
• You can set the reference altitude value within the range of –3,000 to 10,000 meters (–9,840 to
32,800 feet).
• Pressing
A
and
C
at the same time returns to OFF (no reference altitude value), so the watch
performs air pressure to altitude conversions based on preset data only.
3. After the setting is the way you want, push the crown back in to exit the setting screen.
E-58
Advanced Altimeter Mode Operations
Use the information in this section to obtain more accurate altimeter readings, especially while mountain
climbing or trekking.
Using an Altitude Differential Value
If you specify a reference altitude, the second hand of the watch will
indicate the difference between the current altitude and the reference
altitude. The displayed altitude differential value is updated each time the
watch obtains a new altitude reading value.
• Depending on the currently selected display range, the allowable
range for the altitude differential value is 100 meters to –100 meters
(100 meters = 328 feet), or 1,000 meters to –1,000 meters (1,000
meters = 3,280 feet).
• If a reading value is outside the allowable range either (
OVER
) or
(
UNDER
) appears on the digital display.
• The second hand will move to 9 o’clock if a sensor reading could not
be taken for some reason or if the reading is outside the allowable
range.
• See “Using the Altitude Differential Value While Mountain Climbing or
Hiking” (page E-59) for some real-life examples of how to use this
feature.
Altitude differentialAltitude differential
E-59
Specifying the Altitude Differential Measurement Range
You can use the procedure below to select either ±100 meters or ±1,000
meters as the altitude differential measurement range.
Relative Altitude Measurement Range Display Unit
±100 meters (±328 feet) 5 meters (16 feet)
±1000 meters (±3280 feet) 50 meters (164 feet)
To specify the altitude differential measurement range
1. In the Altimeter Mode, pull out the crown.
• This will cause the current altitude reading value to appear.
• The timekeeping (hour, minute, second) hands will move to 2
o’clock.
2. Press
B
twice.
• This will cause DIFF to appear on the digital display, along with the
fl ashing current altitude differential measurement range setting.
3. Rotate the crown to select either 100 meters (
100m
) or 1,000 meters
(
1000m
) as the altitude differential measurement range.
4. After the setting is the way you want, push the crown back in to exit the
setting screen.
Using the Altitude Differential Value While Mountain Climbing or Hiking
After you specify the altitude differential start point while mountain climbing or hiking, you can easily
measure the change in the altitude between that point and other points along the way.
Altitude differentialAltitude differential
E-60
To use the altitude differential value
1. In the Altimeter Mode, check to make sure that an altitude reading is
on the display.
• If an altitude reading is not displayed, press
A
to take one. See “To
take altitude readings” (page E-55) for details.
2. Use the contour lines on your map to determine the difference in
altitude between your current location and your destination.
3. In the Altimeter Mode, hold down
D
for at least two seconds to specify
your current location as the altitude differential start point.
• DIFF RESET and then RESET will appear. The watch will take an
altitude reading, and the second hand will indicate the altitude
differential. ±0 (±0 meters) will be displayed as the altitude
differential at the reference point.
4. While comparing the altitude difference you determined on the map
and the watch’s altitude differential value, advance towards your
destination.
• If the map shows that the difference in altitude between your
location and your destination is +80 meters for example, you know
you will be nearing your destination when the displayed altitude
differential value shows +80 meters.
Current
location
Destination
altitude
Current
location
Destination
altitude
Altitude Differential (Reference
location, so ±0 m is indicated.)
Current altitude
Altitude Differential (Reference
location, so ±0 m is indicated.)
Current altitude
E-61
The altitude differential with the reference location is indicated by the second hand (altitude differential
indicator) as shown in the illustration below.
Unit: 50m (164ft)
Unit: Meters
Unit: 5m (16ft)
−500m (−1640ft)
−50m (−164ft)
−100m (−328ft)
−1000m (−3280ft)
1000m (3280ft)
500m (1640ft)
100m (328ft)
Example:
Altitude
differential of
−30 (300)
meters
Indication range:
±100 (1000) meters
50m (164ft)
00
E-62
•
When
±100m
is selected for the altitude differential measurement range, the
(over) indicator
appears any time the differential is greater than +100 meters (+328 feet). The (under) indicator
appears any time the differential is greater than −100 meters (−328 feet). If either of these indicators
appears, change the range setting to
±1000m
.
•
When
±1000m
is selected for the altitude differential measurement range, the
(over) indicator
appears any time the differential is greater than +1000 meters (+3280 feet). The (under) indicator
appears any time the differential is greater than −1000 meters (−3280 feet).
• The second hand will move to 9 o’clock if a reading is outside the altimeter measurement range (−700
to +10,000 meters (–2,300 to 32,800 feet)), or if a reading error occurs.
Types of Altitude Data
Your watch can record two types of altitude data in its memory: manually saved data and auto save
values.
• Use the Data Recall Mode to view data stored in memory. See “Viewing Altitude Records” (page E-83)
for details.
E-63
Manually Saved Records
Any time you perform the procedure below in the Altimeter Mode, the watch will create and store a record
with the currently displayed altitude reading, along with the date and time the reading was taken. There is
enough memory to store up to 30 manually saved records, which are numbered from
-01-
through
-30-
.
To save a reading manually
1. In the Altimeter Mode, check to make sure that an altitude reading is
on the display.
• If an altitude reading is not displayed, press
A
to take one. See “To
take altitude readings” (page E-55) for details.
2. Hold down
A
until
REC
fl ashes and then stops fl ashing.
• This will save the currently displayed altitude reading in a manually
saved record, along with the time and date of the reading.
• The watch will return to the Altimeter Mode screen automatically
after the save operation is complete.
• There is enough memory to store up to 30 manually saved records.
If there are already 30 manually saved records in memory, the
above operation will cause the oldest record to be deleted
automatically to make room for the new one.
Operation Guide 5365
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Casio 5365 - PRW-6000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Casio 5365 - PRW-6000 in the language / languages: English as an attachment in your email.

The manual is 1,97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Casio 5365 - PRW-6000

Casio 5365 - PRW-6000 User Manual - German - 15 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info