Manual Casio 3197 (page 4 of 5) (English)

636314

Zoom out

Zoom in

1/5

Operation Guide 3197

• Performing illumination, or beeper operations during a

short period may cause

(recover) to appear on the

display.

After some time, battery power will recover and

(recover) will disappear, indicating that the above

functions are enabled again.

• If

(recover) appears frequently, it probably means

that remaining battery power is low. Leave the watch in

bright light to allow it to charge.

Recover indicator

Charging Precautions

Certain charging conditions can cause the watch to become very hot. Avoid leaving

the watch in the areas described below whenever charging its rechargeable battery.

Also note that allowing the watch to become very hot can cause its liquid crystal

display to black out. The appearance of the LCD should become normal again when

the watch returns to a lower temperature.

Warning!

Leaving the watch in bright light to charge its rechargeable battery can cause it

to become quite hot. Take care when handling the watch to avoid burn injury.

The watch can become particularly hot when exposed to the following

conditions for long periods.

• On the dashboard of a car parked in direct sunlight

• Too close to an incandescent lamp

• Under direct sunlight

Exposure Level (Brightness)

Outdoor Sunlight (50,000 lux)

Sunlight Through a Window (10,000 lux)

Daylight Through a Window on a Cloudy Day (5,000 lux)

Indoor Fluorescent Lighting (500 lux)

Approximate

Exposure Time

5 minutes

24 minutes

48 minutes

8 hours

Charging Guide

The following table shows the amount of time the watch needs to be exposed to light

each day in order to generate enough power for normal daily operations.

• For details about the battery operating time and daily operating conditions, see the

“Power Supply” section of the Specifications.

• Stable operation is promoted by frequent exposure to light.

Recovery Times

The table below shows the amount exposure that is required to take the battery from

one level to the next.

Approximate Exposure Time

Level 5 Level 4 Level 3 Level 2 Level 1

3 hours 26 hours 7 hours

10 hours 127 hours 34 hours

19 hours 259 hours 70 hours

226 hours - - - - - - - - - - - - - - - -

Exposure Level

(Brightness)

Outdoor Sunlight

(50,000 lux)

Sunlight Through a

Window (10,000 lux)

Daylight Through a

Window on a Cloudy

Day (5,000 lux)

Indoor Fluorescent

Lighting (500 lux)

• The above exposure time values are all for reference only. Actual required exposure

times depend on lighting conditions.

▲

Reference

This section contains more detailed and technical information about watch operation.

It also contains important precautions and notes about the various features and

functions of this watch.

Stopwatch

• You can use lap time measurement to time how long it takes to complete a specific

portion (such as a single lap) of a race.

• You can use split time measurement to time how long it takes to get from the start to

a specific point in a race.

Memory Management

Each time you press D to start a new elapsed time or lap/split operation in the

Stopwatch Mode, the watch automatically creates a new “log” in its memory. The log

remains open for data storage until you permanently close it by pressing A to clear

the stopwatch to all zeros.

The watch has enough memory to hold up to 121 records. Each log title screen (start

date and time) and lap/split time uses up one record.

• A log title screen identifies a single elapsed time operation, from the start up to the

point the stopwatch is reset to all zeros.

• A lap/split time record is stored under a log title screen each time you perform a lap/

split operation.

Example 1

Single elapsed time measurement

Log title screen + 120 lap records = 121 records

Example 2

Multiple elapsed time measurements

Measurement 1 log title screen + 60 lap records = 61 records

Measurement 2 log title screen + 59 lap records = 60 records

• Use the Recall Mode to view stopwatch records.

• If watch memory is already full when you perform a stopwatch button operation that

creates a new log, the oldest log in memory and all of its records are deleted

automatically to make room for the new log.

• If you are adding records to the only log in memory and watch memory becomes

full, adding another record causes the oldest record in the log to be deleted

automatically to make room for the new record.

• If you are adding records to a log when there are multiple logs in memory and watch

memory becomes full, adding another record causes the oldest log in memory and

all of its records to be deleted automatically to make room for new records.

How Stopwatch Data is Stored

The following table describes how data is stored when you perform the various button

operations described in “To measure times with the stopwatch”.

Stopwatch Button Operation

D Start (from all zeros)

D Stop

D Re-start

A Lap/Split

A Clear

Data Store Operation

Creates a new log for the current date. (The log

is updated as timing progresses.)

Time measurement stops, without storing data in

memory.

Time measurement re-starts, without storing

data in memory.

Creates new record: displayed lap/split times

(Stopwatch display is cleared to all zeros.)

Button Operation Tone

The button operation tone sounds any time you press one

of the watch’s buttons. You can turn the button operation

tone on or off as desired.

• Even if you turn off the button operation tone, alarms,

the Hourly Time Signal, and other beepers all operate

normally.

To turn the button operation tone on and off

1. In the Timekeeping Mode, hold down A until the city

code starts to flash, which indicates the setting screen.

2. Press C nine times until the current button operation

tone setting (

or ) appears.

3. Press D to toggle the setting between

(tone on)

and

(tone off).

4. Press A to exit the setting screen.

• The mute indicator is displayed in all modes when the

button operation tone is turned off.

Mute indicator

Power Saving Function

When turned on, the Power Saving function enters a

sleep state automatically whenever the watch is left in an

area for a certain period where it is dark. The table below

shows how watch functions are affected by the Power

Saving function.

Elapsed Time

in Dark

60 to 70 minutes

6 or 7 days

Display

Blank, with Power Saving

indicator flashing

Blank, with Power Saving

indicator not flashing

Operation

All functions enabled, except for the

display

Beeper tone, illumination, and display

are disabled.

• Wearing the watch inside the sleeve of clothing can cause it to enter the sleep state.

Power saving indicator

• The watch will not enter the sleep state between 6:00 AM and 9:59 PM. If the watch

is already in the sleep state when 6:00 AM arrives, however, it will remain in the

sleep state.

To recover from the sleep state

Perform any one of the following operations.

• Move the watch to a well-lit area.

• Press any button.

To turn Power Saving on and off

1. In the Timekeeping Mode, hold down A until the city

code starts to flash, which indicates the setting screen.

2. Press C 11 times until the Power Saving on/off screen

appears.

3. Press D to toggle Power Saving on (

) and off ( ).

4. Press A to exit the setting screen.

• The Power Saving indicator is on the display in all

modes while Power Saving is turned on.

On/Off status

Auto Return

• If you do not perform any operation for about two or three minutes while a setting

screen (with a flashing setting) is on the display, the watch will exit the setting screen

automatically.

Scrolling

The B and D are used in various modes and setting screens to scroll through data

on the display. In most cases, holding down these buttons during a scroll operation

scrolls at high speed.

Initial Screens

When you enter the World Time Mode or Alarm Mode, the data you were viewing

when you last exited the mode appears first.

Timekeeping

• Resetting the seconds to 00 while the current count is in the range of 30 to 59

causes the minutes to be increased by 1. In the range of 00 to 29, the seconds are

reset to 00 without changing the minutes.

• The year can be set in the range of 2000 to 2099.

• The watch’s built-in full automatic calendar makes allowances for different month

lengths and leap years. Once you set the date, there should be no reason to change

it except after you have the watch’s battery replaced.

• The current time for all city codes in the Timekeeping Mode and World Time Mode is

calculated in accordance with the Coordinated Universal Time (UTC) for each city,

based on your Home City time setting.

World Time

• The seconds count of the World Time is synchronized with the seconds count of the

Timekeeping Mode.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Casio 3197 in the language / languages: English as an attachment in your email.

The manual is 0,55 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Casio 3197

Casio 3197 User Manual - German - 5 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Casio 3197 Manual

Product: