799647
7
Zoom out
Zoom in
Previous page
1/66
Next page
7
Replacement of carbon brush (Fig D)
- Remove the carbon brush lid (6) with a screw-
driver.
- Replace the carbon brush.
- Install the carbon brush lid (6) with a screwdriver.
Use:
- Unroll the cable completely before plugging it in.
- Connect the appliance to the mains.
- Assemble the sanding Sheet
- Turn the appliance on, by using the on/off button
(1).
- Place the appliance against the surface you want
to work.
- Slowly move the appliance over the workpiece,
- Do not apply excessive pressure against the work-
piece.
- Apply uniform sanding pressure against the work-
piece to increase performance and working life of
the sander and the sanding sheet.
Once you have nished using the appliance:
- Stop the appliance using the on/off switch (1).
- Unplug the appliance from the mains.
- Clean the appliance.
Cleaning
- Disconnect the appliance from the mains and al-
low it to cool before undertaking any cleaning task.
- Allow it to cool before undertaking any cleaning
task.
- Clean the electrical equipment and the mains
connection with a damp cloth and dry. DO NOT IM-
MERSE IN WATER OR ANY OTHER LIQUID.
- Clean the equipment with a damp cloth with a few
drops of washing-up liquid and then dry.
- Do not use solvents, or products with an acid or
base pH such as bleach, or abrasive products, for
cleaning the appliance.
- Do not let water or any other liquid get into the
air vents to avoid damage to the inner parts of the
appliance.
- Never submerge the appliance in water or any
other liquid or place it under running water.
- If the appliance is not in good condition of cleanli-
ness, its surface may degrade and inexorably affect
the duration of the appliance’s useful life and could
become unsafe to use.
Supplies
- Always use original supplies, designed specically
for your appliance model.
- These supplies are available in specialist shops.
Anomalies and repair
- Take the appliance to an authorised technical
support service if a product damage or other
problems arise. Do not try to dismantle or repair
without assistance, as this may be dangerous.
- If the connection to the mains has been damaged,
it must be replaced and you should proceed as you
would in the case of damage.
Specifications:
CSS710VCE
- Rated power 710 W
- Rated voltage 230 V~
- No load speed 1500-3000 /min
- Sandpaper dimensions Ø 180
- Weight 2.3 Kg
- Sound Pressure level (LpA) = 90.9dB(A), KpA = 3dB
- Sound Power level (LwA) = 101.9 dB(A), KWA = 3dB
- Vibration= 2.415m/s2, K= 1,5 m/s2
NB: These specications are subject to change without
notice of purpose of improvement.
NB: By virtue of the conditions of fabrication of this
product, the maximum absorbed power can differ from
that specied.
NB: By virtue of the conditions of fabrication of this
product, the maximum used power can differ from that
specied.
Wear hearing protection
-Measured sound level determined according
EN60745
-The vibration emission level given in this information
sheet has been measured according EN60745 and
may be used to compare one tool with other. It may be
used for a preliminary assessment of exposure
-The vibration value during actual use of the power
tool can differ from the declared total value depending
on the way in which tool is used
-It’s necessary identify safety measures to protect the
operator that are based on an estimation of exposure
in the actual conditions of use (taking account of all
parts of the operating cycle such as the times when
the tool is switched off and when it is running idle in
addition to the trigger time).
For EU product versions and/or in case that it is
requested in your country:
Ecology and recyclability of the product
- Ensure that the voltage indicated on the rating label
matches the mains voltage before plugging in the ap-
pliance.
Sand paper Replacement (Fig B)
- To remove the sand paper (9) grasp it and pull it off
from the Viscid disc (8).
- Pay attention that punched holes of the sand paper
(9) match with the holes of the Viscid disc (8).
- Position the sand paper (9) ush alongside one edge
of the Viscid disc (8).
- Lay the sand paper (9) onto the Viscid disc (8) and
press rmly.
- To remove the sand paper (9) grasp it and pull it off
from the Viscid disc (8).
Replacement of Viscid disc (Fig B)
- Remove the sand paper (9).
- Block the rotation of the viscid disc (8)
- Put the allen wrench in to the hexagon hole in the
center of the viscid disc (8)
- Rotate the allen wrench clockwise
- Remove the old viscid disc (8)
- Install the new viscid disc (9)
Electronic speed control (Fig A)
- The speed of the appliance can be regulated by
using the speed regulator control (3). This function
is very useful, as it makes it possible to adapt the
speed of the appliance to the type of work that needs
to be done.
Switch on y Switch off (Fig A)
- Turn the appliance on, by pushing the on/off but-
ton (1)
- To activate the self-locking switch press the locking
button (2) while holding down the on/off button (1).
- To turn the appliance off, press the on/off button (1)
without pressing the locking button (2)
Sanding the corner (Fig C)
- Disassemble the removable lid (10) from the pad
cover (7)
- Rotate the adjust knob (11) anti-clockwise.
- Rotate the pad cover (7) until the desired position.
- Rotate the adjust knob (11) clockwise.
- Sand the corner space.
Connection set for dust outlet (Fig E)
- Connect the dust hose (13) into the dust outlet 12
- Rotate the dust hose (13) clockwise in order to lock
it
- Attach the cloth bag (14) to the dust hose (13)
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Casals CSS710VCE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Casals CSS710VCE in the language / languages: All languages as an attachment in your email.

The manual is 3.82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info