550542

Carrera Digital 124 - 23613 GENTLEMEN RACE Manual

16
Zoom out
Zoom in
Previous page
1/26
Next page
16
Extended Pit Lane function
Pit Lane 30356
1
8
2
7
3
6
5
2
1
8
2
7
3
6
4
5
1
1
8
2
7
3
6
5
4
1
8
2
7
3
6
4
5
3
1
8
2
7
3
6
4
5
65
(only in combination with Pit Lane 30356)
It is possible to activate/deactivate the lap counting function in the
Pit Lane 30356 or Pit Stop Lane 30346 with the Pit Stop Adapter
Unit 30361. Switch off the Control Unit, keep “SPEED” button
5
)
pushed, switch on Control Unit and release “SPEED” button
5
.
By pushing the button again, 1 or 2 LEDs will light depending on
the setting.
• LED 1 = lap counting function deactivated
• LED 1 + 2 = lap counting function activated
Select the desired setting and push or drive a car across the Pit
Lane Sensor, fig.
5
. The settings will now be adopted. Push
“START/ENTER”
3
for leaving the settings again.
Sound ON/OFF
1
8
2
7
3
6
4
5
2
1
8
2
7
3
6
4
5
1
1
8
2
7
3
6
4
5
3
The confirmation sound when crossing the sensors and the key
sound can be switched off. Switch off the Control Unit and keep the
“START/ENTER” button
3
pushed, switch on the racetrack and
release “START/ENTER”
3
again. The acknowledgement sound
for switching on the Control Unit cannot be switched off however.
Reset function
1
8
2
7
3
6
4
5
2
1
8
2
7
3
6
4
5
1
1
8
2
7
3
6
4
5
3
To restore the Control Unit to factory settings the Control Unit offers
a reset function.
Switch off the Control Unit and keep the “ESC/PACE CAR”
4
but-
ton pushed; switch on the ractrack and release the button again. All
previous settings for speed, braking performance, tank fuel capac-
ity, sound and lap counting will be restored to factory settings. The
cars´ settings will remain unaffected by this measure unless they are
placed on the racetrack.
Factory settings:
• speed = 10
• braking performance = 10
• tank capacity = 7
• sound = ON
• display of position for Autonomous and Pace Car = OFF
Energy-saving mode
After 20 minutes of non-usage the Control Unit switches to energy-
saving mode and all displays such as Position Tower, Driver Dis-
plays and Startlight are turned off. To reactivate shortly press any
speed controller´s tappet or push lane-change button at the speed
controller or control key at the Control Unit. All settings will be kept.
Replacement of double
contact brushes and guide keel
1 2
43
In case the car is lifted, the rocker bar folds up slightly (fig.
1
).
For changing the guide keel or the double contact brushes the
rocker bar can be folded up widely according to fig.
2
.
3
For changing the guide keel and the double contact brushes the
guide keel should be removed first.
4
Afterwards both double contact brushes can be removed and
changed. Please take care that in stage one the upper contact
brush
4
a
is only pulled out partly and in stage two the double
contact brush is pulled out completely with the contact brush
4
b
For inserting please proceed the same way.
Height adjustment
car chassis
1 2
3 4
Before you can begin adjusting the chassis and the magnets it is
necessary to detach the car body from the vehicle. Remove the
mounting screws on the underside of the car and lift off the car body.
Adjusting the height of the front axle
1
Remove the two screws from the front axle mounting and detach
the entire front axle including the mounting from the chassis.
2
Detach the mounting from the axle, turn it through 180 degrees
3
and insert the axle back into the mounting
4
. Now you can return
the front axle and mounting unit to the chassis.
1 2
3 4
5
Adjusting the height of the rear axle
To simplify the procedure, carefully detach the plug connection bet-
ween the motor and the circuit board
1
. Remove the two screws
from the motor block unit and detach the magnet retainer from the
chassis. Now remove the two rear screws and detach the entire
motor block
2
.
Turn the motor block around and remove the two screws from the
rear axle mounting. Remove the spacer plates and the rear axle unit
including the mounting
3
. To adjust the height, place the spacer
plate in the motor block
4
and tighten the screws of the rear axle
unit.
5
.
1
2 3
Adjusting the central magnet
If required, the central magnet can also be adjusted. Remove the
magnet unit from the chassis in its entirety
1
, turn it horizontally by
180 degrees
2
and return it to the chassis. Then mount the magnet
retainer
3
and restore all plug connections.
Changing the light board
1 32
… 16 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Carrera Digital 124 - 23613 GENTLEMEN RACE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Carrera Digital 124 - 23613 GENTLEMEN RACE in the language / languages: English, German, French as an attachment in your email.

The manual is 9,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info