551014
14
Zoom out
Zoom in
Previous page
1/116
Next page
14
ON
ON
1
1
Changeover between
Beginner / Advanced mode
The Carrera RC helicopter and the
remote control are frequency bound at
purchase. Should there occur any prob-
lems with the communication between
the Carrera RC helicopter and the
remote control at the beginning, please
carry out a new frequency bind.
• Connect the plug-in connection at the model and switch on the model at the ON/OFF
switch.
• The LED in the helicopter now flashes in rhythmically-accelerating sequence.
• Switch on the controller at the ON/OFF switch. While connecting, the controller
emits a signal tone.
• Place the charged helicopter on a flat surface.
Allow the helicopter a few moments until the system is correctly initialised and is
ready for operation.
The control LED now lights continuously once again, indicating that the connection
is ended.
When controller and helicopter are initially switched on, the model is in Beginner“
mode.
To change between Beginner and Advanced mode when the controller and helicopter
are switched on, press the right-hand joystick in vertically from above.
The changeover can also be made while the machine is in flight. When changing over
into Advanced mode, you will hear a single beep“ signal and when changing into
Beginner modus a „beep-beep“ will be heard.
The helicopter reacts more sensitively in Advanced mode to your commands on
the controller than it does in Beginner mode.
Note: you should first practice flying with the helicopter in Beginner mode until
you are fully in control of the model. Only then should you switch over to Advanced
mode. The helicopter will react in Advanced mode more sensitively to your commands
on the controller!
Checklist for flight preparation
Preparing the first flight
This checklist does not replace the contents of the operating instructions.
Although it can be used as a quick-start-guide we strongly advise to first read the
operating instructions in detail before you proceed.
Check the contents of the package
Connect the charger to the power socket
Charge the li-ion-battery as described in the sectionCharging the li-ion battery“.
Fit four AA ba
tteries in the controller, making sure their polarity is correct.
Look for a suitable environment for flying
Place the helicopter on a flat surface
Switch on first the helicopter and then the controller.
Check the control system
Make yourself familiar with the control system
Trim the helicopter if necessary as described on P. 16, so that when hovering,
the helicopter no longer moves from the spot without the controls being touched.
• Fly the model
• Land the model
Switch the model off
• Always switch off the remote control last
This checklist does not replace the contents of the operating instructions.
Although it can be used as a quick-start-guide we strongly advise to first read the
operating instructions in detail before you proceed.
• Connect the plug-in connection at the model and switch on the model at the
ON/OFF switch
• The LED in the helicopter now flashes in rhythmically-accelerating sequence.
• Switch on the controller at the ON/OFF switch. While connecting, the controller
emits a signal tone.
• Place the charged helicopter on a flat surface.
• Allow the helicopter a few moments until the system is correctly initialised and
is ready for operation.
• The LED in the helicopter is not lit continuously and the controller is no longer
emitting its signal tone.
• The helicopter is now ready to be flown.
If the helicopter fails to display any function, connect the model with the
controller as necessary, as shown below.
• Fly the model
• Land the model
Switch the model off at the ON/OFF switch and unplug the connection in the
helicopter.
Always switch off the remote control last
Frequency bind between
model and remote control
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Carrera 501006 Spider Fox at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Carrera 501006 Spider Fox in the language / languages: All languages as an attachment in your email.

The manual is 5,97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Carrera 501006 Spider Fox

Carrera 501006 Spider Fox Additional guide - English, German, French - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info