680508

Cardo Door Magic 1000 Manual

13
Zoom out
Zoom in
Previous page
1/216
Next page
Magic 1000 N000925 12/2010 11 / 214
Deleting (all) remote transmitter(s):
During one of the 3 status messages A, B or C (seeChapter
10), press the pushbuttons and simultaneously for >6
seconds, FL flashes in the display. The status message
reappears after 3 seconds.
CAUTION: Mishandling the product can result in
injuries or material damage. Follow the basic safety
rules:
When opening or closing the door, do not block the interior or
exterior swivel ranges. Keep children away.
The door movements can be activated or stopped using the
remote transmitter provided or via switching elements such
as the wall keypad, which can be connected if desired.
Optional external features (such as the EMERGENCY
STOP) can also be connected to the door operator.
The operator must be connected to a door before
it is used. If it is not, incorrect load values will be
taught in to the electronic system. This can cause
malfunctions.
Switch on programming mode
During one of the 3 status messages A, B or C (seeChapter
10) press the Menu pusbutton for longer than 1.5
seconds. The display changes to the menu (D).
Select programming menu
Select the desired menu with the pushbuttons and .
Show / change menu value
Displays: Press the Menu pushbutton for less than 1.5
seconds, the menu value (E) is displayed.
Change: Change the value with the pushbuttons and .
Save: Press the Menu pushbutton for less than 1.5
seconds, the programming menu (D) is displayed.
Exit programming mode
Press the Menu pushbutton for longer than 1.5 seconds,
the display changes to the status message, changes are
saved.
If no key is pressed within 15 seconds during programming, it
automatically exits the programming mode.
ATTENTION: If the values of the programming
menu A0 to A4 are changed, the load switch-off no
longer provides any protection! Teach the door operator in
again before re-commissioning. For this carry out Teaching in
the door operator (Chapter 15) .
17 Operation
18 Programming
Factory setting
Menu
Function, setting range, unit
A0 Length SOFT RUN OPEN in 7cm
000..009
002
A1 Length SOFT RUN CLOSE in 7cm
000..009
004
A2 Soft running speed (CLOSE) mm/s
000= 50...009= 140
005
A3 Backjump, OFF= 000 ON= 001 001
A4 Change in direction, OFF= 000 ON= 001
Setting (with +/-) only possible if EMERGENCY
STOP plug (1, green) is unplugged.
000
A5 Added load OPEN
1)
000..009 003
A6 Added load CLOSE
1)
000..009 003
A7 Door type: Overhead sectional door/one-piece
door = 000
Side sectional door* = 001
Side sectional door with soft start = 002
* Obstruction release also in OPEN direction
000
A8 Warning time (OPEN/CLOSE) 001=2sec...
008=16sec
000
A9 Accessory card
000= ZKMagicS
001= ZKMagic
000
b0 Relay 1 (with ZKMagic accessory card)
000= no function
001= E-lock
002= warning light *
002= photo cell test* (interruption transmitter
voltage)
004= status display*: Door in end position OPEN
005= status display*: Door in end position
CLOSED
006= green light*
007= red light*
* if A9= 001
000
b1 Relay 2 (with ZKMagic accessory card)
000= no function
001= E-lock*
002= warning light *
002= photo cell test* (interruption transmitter
voltage)
004= status display*: Door in end position OPEN
005= status display*: Door in end position
CLOSED
006= green light*
007= red light*
* if A9= 001
000
b2 Closing edge protection, for accessory card
ZKMagic and if A9= 001
000= OFF 001= OSE 002= 8k2
000
b3 Empty run detection 000= OFF 001= ON 001
b4 Automatic closing
1)
*, secs. and min.
000= OFF
001.0.010 keep-open time secs.*
(001 = 5secs... 010 = 50secs)
011..040 keep-open time min*
(011=1min... 040=30min) * plus warning time
* only active if door was fully opened
000
b6 Maintenance interval
000= OFF
001..009 (1,000 door movements)
Example: 005 = 5,000 door movements
The operator lighting flashes after every door
movement when the maintenance interval has run
out. A misadjustment resets the counter of the
maintenance interval.
000
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cardo Door Magic 1000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cardo Door Magic 1000 in the language / languages: All languages as an attachment in your email.

The manual is 6,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info