Manual Carat T-4010 (page 13 of 52) (English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish)

816467

Zoom out

Zoom in

1/52

DANSK

NOTE!

In emergency, press the red stop button on the

switch by the le hand.

Cutting method: 45° bevel cuts

The machine oers the possibility of performing 45° bevel

cuts. To perform 45° bevel cuts, proceed as follows:

1. Pull the cutting table forward to free place for the cutter

head.

2. Loosen the rear nut on the cutter head.

3. Tilt the cutter head until the 45° position is reached.

4. Tighten firmly the rear nut on the cutter head again.

5. Fix the cutter head with the locking lever in the lowest

position.

6. Put the material to be cut onto the cutting table and

position it directly at the material stop.

7. Check the position of the material using the back

square.

8. Start the machine.

9. Grab the handle of the cutting table by the le hand

and the cutting head handle by the right hand.

10. Slowly slide the cutting table forward, without pressure,

against the cutting wheel, and pull it back aer cutting

through the material.

NOTE!

In emergency, press the red stop button on the

switch by the le hand.

NOTE!

The cutting wheel, irrespective of its position or

the position of the cutter head, may touch neither the

table, nor the back square!

To bring the cutter head aer this cutting procedure

back to 90° position, proceed as follows:

1. Switch o the machine -> the cutting wheel must

stop rotating!

2. Loosen the locking lever and fix the cutter head

again in the top position.

3. Loosen the rear nut on the cutter head.

4. Tilt the cutter head until the 90° position is reached.

5. Tighten firmly the rear nut on the cutter head again.

6. Fix the cutter head by the locking lever again.

NOTE!

Hold firmly the cutter head with the hand

in the 90°¬ position. Tightening the nut can turn the

square back so that the angle of the cutter head is

not exactly 90°.

NOTE!

The cutting wheel, irrespective of its position

or the position of the cutter head, may not touch the

cutting table!

6.4.2 Water supply

Heavily polluted water decreases the service life of the

water pump and cutting wheel.

For frequent use, change water several times a day, and

collect, filter and dispose of the cutting mud

Clean the suction strainer of the water pump every time

the water is changed

6.5 Stop cutting operation

Use the red stop switch on the motor to stop the machine.

. MAINTENANCE & CLEANING

Before performing any maintenance, make sure the

machine is disconnected from electrical power.

For long-term quality, please perform the following

maintenance actions aer using the machine

- Visually inspect the entire machine.

- Clean the flange and blade mounting.

- Clean engine (housing + cooling fans), water tank, water

pump, water pump filter, water hoses and nozzles, table

guide rails, table wheels.

- Make sure all bolts and screws are tightened.

Before using the machine, make sure that all the above

actions have been performed.

. DISPOSAL

If no return or disposal agreement was made, send the

dismantled components for recycling:

- Scrap metal parts.

- Hand over plastic parts for recycling.

- Dispose of other components assorted according to

material characteristics.

EU countries only

Electric waste is recyclable and must not be

disposed of in the household waste!!

According to the European directive 2012/19/EU on

electrical and electronic waste and version transposed

into national law, used power tools must be collected

separately and sent for recycling in an environmental-

friendly manner.

. GENERELT

1.1 Betjeningsvejledning

Denne betjeningsvejledning giver vejledning i sikker og

eektiv dri og bør danne grundlag for enhver handling,

der involverer denne maskine. Det er en integreret del

af maskinen, som skal opbevares i nærheden, så den er

lettilgængelig for drispersonalet.

Forudsætningen for sikker betjening er, at alle

sikkerheds- og håndteringsinstruktioner overholdes.

Før arbejdet påbegyndes, skal personalet derfor læse

betjeningsvejledningen omhyggeligt igennem og

forstå den.

Desuden skal de regler for ulykkesforebyggelse,

der gælder på maskinens drissted, samt generelle

sikkerhedsforskrier overholdes.

1.2 Symbolforklaring

Advarsler og sikkerhedsinstruktioner

Advarsler og sikkerhedsinstruktioner i vejledningen er

vist med piktogrammer i grå kasser

FARE!

... henleder opmærksomheden på en umiddelbar

fare, der, hvis den ikke undgås, kan resultere i alvorlig

personskade eller endog død.

VÆR OPMÆRKSOM!

... henleder opmærksomheden på potentielt

farlige situationer, der, hvis de ikke undgås, kan resultere

i materiel skade.

... kendetegner fare forårsaget af elektrisk strøm.

Manglende overholdelse af sikkerhedsinstruk-

tionerne medfører risiko for alvorlig eller dødelig

personskade.

… kendetegner fare for knusning.

Manglende overholdelse af sikkerhedsinstruk-

tionerne medfører risiko for alvorlige personskader

forårsaget af bevægelige dele.

... kendetegner fare forårsaget af varme overflader.

Manglende overholdelse af sikkerhedsinstruk-

tionerne medfører risiko for forbrændinger og alvorlige

hudskader forårsaget af varme

... kendetegner fare ved flytning af diamantklinger.

Manglende overholdelse af sikkerheds-

instruktionerne medfører risiko for snitsår og alvorlige

hudskader forårsaget af roterende diamantklinger.

1.3 Ansvarsbegrænsning

Alle data og anvisninger i denne vejledning er udarbejdet

under hensyntagen til gældende standarder og

bestemmelser, det aktuelt tekniske niveau og vores

mangeårige indsigt og erfaring.

Producenten påtager sig intet ansvar for skader

forårsaget af:

- Manglende overholdelse af betjeningsvejledningen.

- Utilsigtet anvendelse.

- Ansættelse af ufaglært og uvejledt personale.

- Uautoriserede konverteringer.

- Tekniske ændringer.

- Anvendelse af ikke-godkendte reservedele.

De ansvarsområder, der er aalt i leveringskontrakten,

de generelle vilkår og betingelser samt producentens

leveringsbetingelser og de lovbestemmelser, der er

gældende på tidspunktet for kontraktens indgåelse,

finder anvendelse.

Garanti

Producenten garanterer funktionsevnen for den anvendte

procesteknologi og de identificerede ydelsesparametre.

Garantiperioden begynder med fejlfri levering.

Garantibetingelser

12 måneder eer leveringen af mekaniske og elektriske

komponenter til etskisdri, bortset fra sliddele og

værktøj.

Garantikravet udløber, hvis systemet ikke er installeret og

opstartet af vores eksperter.

Garantien er udvidet til at gælde reservedele. Omfatter ikke

følgeskader.

Skader forårsaget af naturligt slid, mangelfuld vedlige-

holdelse, manglende overholdelse af drisforskrierne,

overdreven belastning og brug af uegnet udstyr er ikke

omfattet af garantien.

. SIKKERHED

2.1 Tilsigtet anvendelse

T-3510, T-4010, T-5010, T-6010, T-7010

er konstrueret til at skære i våde, faste

konstruktionsmaterialer såsom: klinker, mursten,

betonblokke, ildfaste produkter, naturlige og kunstige

stenprodukter samt fliser og keramik.

- Eventuelle erstatningskrav som følge af utilsigtet brug er

udelukket.

- Operatøren alene er ansvarlig for alle skader som følge af

utilsigtet brug.

2.2 Rationelt forudsigeligt misbrug

Enhver brug af maskinen, ud over tilsigtet brug, skal

betragtes som utilsigtet og er dermed forbudt.

Dette gælder også for:

- Tilskæring af andre materialer end de angivne.

- Tilskæring uden eller med åben

diamantklingeafskærmning.

- Tilskæring uden vand.

- Fjernelse af afskårede stykker fra pendulskæreprocedurer

(lodret nedstikning i stenmaterialer ovenfra).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Carat T-4010 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish as an attachment in your email.

The manual is 4.81 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Carat T-4010 Manual

Product: