816467

Carat T-4010 Manual

12
Zoom out
Zoom in
Previous page
1/52
Next page
2322
ENGLISH
packaging on a regular basis. If necessary, renew or replace
conservation materials.
. TRANSPORT
ATTENTION!
Damage through improper transportation!
Improper transportation can result in considerable
damage of the machine and objects in the vicinity.
Before every transport:
- The cutter head must be locked.
- The cutter head must be lowered and locked.
- The cutting table must be secured by the table lock
(for table saw machines).
- The machine must be disconnected from power supply.
Due to two transport rollers, the machine can be
transported by one or two persons who can use transport
handles.
Instruction of using crane liing eyes
The machine is designed for crane transport by means of
the liing eye.
Always check the tighteness of the liing eyes before using
it to transport the machine. To avoid damage, also check
that the liing straps do not touch the motor when liing.
CAUTION:
Risk of injury due to improper handle when it is
transported by crane.
CAUTION:
Risk of injury by standing under the machine when
it is transported by crane.
CAUTION:
Risk of injury of falling material from the working
table, it is not allowed to have any material on working
table when it is transported.
Crane liing eyes MS400A / MS500A / MS600A
. INSTALLATION
5.1 Connection
Before connecting the machine to the power source,
make sure that:
- Voltage / phase of the power supply, match the date on
the type plate of the motor and machine.
- The power supply line is grounded according to the safety
provisions.
- The wire size of the extension cord is suicient, H07RNF
3x2.5 mm² up to 50m for 230V.
5.2 Mounting a diamond blade
To mount a new diamond blade or replace the used one,
proceed as follows:
1. Switch o the machine and interrupt the power supply
by pulling the mains cable from the mains outlet.
2. Loosen the screws on the diamond blade guard so as to
be able to remove the front half of the diamond blade
guard. For T-7010, aer loosening the screw on back
of blade guard, disconnect the quick release of water
connector on top of blade guard, then remove the blade
guard.
3. Loosen the nut of the motor sha and remove the outer
cutter flange.
4. Clean the cutter flange, nut and motor sha.
5. Check the parts for signs of wear.
6. Mount or replace the diamond blade. While doing so,
pay attention to the correct rotation direction of the
diamond blade and motor sha.
7. Replace the outer cutting flange on the motor sha.
8. Screw the nut onto the motor sha again and tighten it
firmly.
9. Replace the front half of the cutting wheel guard to
connect it with the rear half.
10. Tighten firmly the screws on the cutting wheel guard.
NOTE!
The arrow on the cutting wheel indicates
correct rotation direction.
NOTE!
The cutting wheel, irrespective of its position or
the position of the cutter head, may not touch the table!
5.3 Mounting the transport handles and wheels
Mount the transport handles at the appropriate places on
the base frame using the supplied washers (4x A8,4 ISO
7089) and the screws (4x M8x30 ISO 4017), the spring wash-
ers (4x A8 DIN 127) and the screws (4x M8x20 ISO 4017).
Do the same with the transport wheels. Mount the trans-
port wheels at the appropriate places on the base frame
using the supplied washers (4x A,8,4 ISO 7090), the spring
washers (4x A8 DIN127), the screws (4x M8x25 ISO 4017)
and the nuts (4x M8 ISO 4032).
Mounting the extension table
If you want to work with the extension table, proceed as
follows:
Insert the extension table into the lateral grommets on the
base frame and tighten it with the star grip screws
5.4 Fill the water tank
The water tank must be filled before the machine is
started. Use clear, clean water for this.
ATTENTION!
The water pump may not run without water,
otherwise it can be damaged.
. OPERATION
6.1 Intended working position of the operator
For table saw machines the operator takes position in
front of the machine to be able to slide the cutting table
forwards/backwards and to adjust the cutter head.
6.2 Start-up preparation
To safely use the machine as intended, the following
preconditions must be met:
- The machine stands firmly.
- The water tank is filled with clean, clear water.
- The machine has been checked for damage, loose screw
connections and integrity.
- The water supply is functional.
- Rotation direction arrows on the cutting wheel and guard
match.
- An appropriate cutting wheel must be installed, which
meets optimum conditions.
6.3 Start-up
The machine is switched on by the main switch. For this
purpose, press the green button to start
Aer the start, check the following:
The cooling water must be pumped to the cutting wheel
by the water pump in the suicient quantities and drain o
on both sides. If this is not the case, stop the machine im-
mediately! The motor is equipped with thermal insulation
activated when the temperature rises too high.
Wait approx. 30 minutes before restarting the machine
until the motor cools down
6.4 Cutting operation
6.4.1 Normal cutting in 90° position
When cutting in 90° position, the cutter head remains at a
fixed point. For adjustment, proceed as follows:
1. Switch o the machine -> the cutting wheel must stop
rotating!
2. Loosen the adjusting screw.
3. Set the cutter head in the desired position.
4. Tighten the adjusting screw -> check if the cutter head
is adjusted in height and make sure that it cannot
move.
5. Put the material to be cut onto the table (for table saw
machine position it directly at the material stop).
6. Check the position of the material using the angle stop.
7. Start the motor and the water pump and open the
water tap.
8. Put one hand on the cutter head handle.
9. Then slowly drag the cutter head without pressure over
the material on the table. The blade cuts the material.
NOTE!
The cutting wheel, irrespective of its position or
the position of the cutter head, may not touch the table!
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Carat T-4010 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Carat T-4010 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish as an attachment in your email.

The manual is 4.81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info