816480

Carat SL-1253N DUSTEC Manual

17
Zoom out
Zoom in
Previous page
1/44
Next page
17
ENGLISH
Remove the remaining n of the material with the wedge
[15].
Curved cuts are not possible, the diamond grinding wheels
will jam in the material.
When breaking through walls, e.g. with a rotary hammer,
most of the chipping-o󰀨 of the surface material can be avoi-
ded by rst grinding a slot with maximum grinding depth.
For grinding especially hard material, e.g. concrete with
high pebble content, the diamond grinding wheels can
overheat and get damaged. This is clearly indicated by cir-
cular sparking, rotating with the diamond grinding wheels.
When this occurs interrupt the grinding process and allow
the diamond grinding wheels to cool down. Run the power
tool for a short time at no-load speed.
Working advice
• Be careful grinding slots in structural walls. See section
“Information on Structures”.
• Do not strain the power tool so heavily that it comes to
a standstill.
• Firmly support the work piece, secured against sliding,
e.g. with clamping devices.
• The power tool may only be used for grinding without
the use of water.
• Noticeable decreasing work progress and circular spar-
king indicates the diamond grinding wheels are become
dull. Briey grinding a abrasive material (e.g. limestone
brick) can sharpen the wheels again.(zoals kalkzand-
steen).
Information on Structures
Slots in structural walls are subject to the standard DIN
1053 part 1 or national-specic regulations. These regu-
lations must be observed. Consult the responsible struc-
tural engineer, architect or construction supervisor before
starting.
The permitted slot depth and width depends on the slot
length, wall thickness and the used construction materials.
EMISSION
Vibration emission value ah = 6 m/s².
Uncertainty K < 1.5 m/s².
Typically the A-weighted noise levels of the pro-
duct are: Sound pressure level 93 dB(A); Sound
power level 104 dB(A). Uncertainty K=3 dB.
Measured values determined according to EN 62841.
ENVIRONMENTAL PROTECTION
According to the European regulation 2012/19/
EU, CARAT is responsible to recycle old electric
drill motors. You are therefore requested to re-
turn old CARAT electric drill motors to your local
reseller.
SERVICE AND MAINTENANCE
Pull the mains plug of the power tool from the
socket, before any work on the machine itself.
For safe and proper working, always keep the
machine and ventilation slots clean.
Dismount and clean the diamond grinding wheels and spa-
cers after nishing. Clean the guard and extraction hood.
WARRANTY
For the machine, a guarantee period of 12 months applies
from the moment of delivery. Guarantee claims must be
shown by submission of purchase invoice. The guarantee
includes the repair of defects which have occurred and can
be linked by to material or manufacturing faults.
Not covered by guarantee:
• Defects or damages which have arisen
due to incorrect use or connection.
• Machine overload.
• When maintenance has been carried
out incorrectly or badly.
• Information in the manual has not been
properly followed.
• The machine is used by unqualied persons.
• If the machine is used for purposes
for which it is unsuitable.
• The machine is repaired using unoriginal parts.
• If the machine encryption is damaged or deleted.
• If defects are caused by re, damp and/or transport.
DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product is
in conformity with the following standards or standardized
documents:
EN 62841-1; EN 61000; 2006/42/EC; 2014/30/EC;
2011/65/EU
Director: C.J. van Beek
16-09-2022
CARAT Nederland B.V.
Nikkelstraat 18, 4823 AB Breda, the Netherlands
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Carat SL-1253N DUSTEC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Carat SL-1253N DUSTEC in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish as an attachment in your email.

The manual is 7.63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info