65605
47
Zoom out
Zoom in
Previous page
1/155
Next page
47
Recording
While a time code signal is being received, the [FRAME SETTNG] and [COUNT-UP] settings of the
camcorder will be ignored and the external time code’s drop-frame bit will be used instead (if the
external time code is non-drop frame, “NDF” will appear on the side panel).
The Genlock synchronization stabilizes after approx. 10 seconds. After that, the synchronization
will be maintained even if you disconnect the cable from the GENLOCK terminal.
When an external time code signal is received, the camcorder's own time code will be
synchronized to it and the synchronization will be maintained even if you disconnect the cable
from the TIME CODE terminal. However, performing any of the following actions while the cable is
not connected will cause the time code to lag slightly; the correct time code will be restored once
you reconnect the cable.
- Turning the camcorder off/on.
- Changing the position of the dial to or from .
- Changing the position of the / (card/tape) switch.
- Changing the [SIGNAL STD] or [FRAME RATE] setting.
If the external time code signal is incorrect or there is no input signal, the internal time code
(according to the [TIME CODE]/[COUNT-UP] settings) will be recorded on the tape instead.
If the external Genlock signal is incorrect or there is no input signal, the external time code being
recorded on tape may be incorrect.
When recording in SD mode, Time Code IN is not available if you select the 24F frame rate (the
mode will be canceled and the “TC-(IN OUT)” display on the side panel will disappear).
When the camcorder is set to HD standard, Genlock synchronization is possible even if the
external Genlock signal is in SD standard. However, Genlock synchronization will not be possible
if the external Genlock signal is in HD standard but the camcorder is set to SD standard.
The phase difference between the external Genlock signal and the camcorder is initially set to 0; it
can be adjusted within the range of approx. ±0.4H (-1023 to +1023) with the [SIGNAL SETUP]
[GENLCK ADJST] setting ( 126).
Genlock synchronization is not possible when [SIGNAL STD] is set to [HD] and [SDI SPEC.] is set
to [SD LOCKED].
About the Side Panel Indications
- “GENLOCK” will flash until the synchronization stabilizes and will stay on once the phase
synchronization has stabilized.
- “TC-(IN OUT)” indicates that the Time Code IN or Time Code OUT synchronization is available
with the TIME CODE switch.
- “EXT- LOCK” indicates that the camcorder has locked on to an external time code signal.
47


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Canon XHA1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Canon XHA1 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 8,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Canon XHA1

Canon XHA1 User Manual - German - 163 pages

Canon XHA1 User Manual - Dutch - 159 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info