65605
46
Zoom out
Zoom in
Previous page
1/155
Next page
46
Synchronizing the Camcorders Time Code
You can synchronize this camcorder’s time code to an external time code generator. You can also
include in the recording the user bit signal received from the TIME CODE terminal ( 48). The
camcorder offers the following synchronization options.
Genlock
When a reference sync signal (analog blackburst or tri-level signal) is input through the GENLOCK terminal,
the V and H phases of the camcorder’s time code will automatically be synchronized to it.
Time Code IN
Set the TIME CODE switch to IN to start the Time Code IN mode. An external SMPTE-standard LTC timing
signal received from the TIME CODE terminal will be recorded as the time code on the tape. The user bit of
the external timing signal can also be recorded on tape.
Time Code OUT
Set the TIME CODE switch to OUT to start the Time Code OUT mode. The camcorder’s internal time code is
sent out from the TIME CODE terminal as a standard LTC timing signal.
When [SIGNAL SETUP] [SDI OUTPUT] is set to [ON(OSD)] or [ON], the time code signal will be output also
through the HD/SD SDI terminal.
When [SIGNAL SETUP] [UB OUT] is set to [HD 24P 2:3], the user bit of the time code signal will be 2:3
pulldown data (when recording in 24F mode or playing back movies that are HDV 1080/24p). In other words,
when recording in 24F mode or playing back movies that are HDV 1080/24p, the signal is converted to 60i
using the 2:3 pulldown method and output from the HD/SD SDI terminal. An external device can receive the
data used in this conversion (2:3 pulldown data) to convert the signal to 1080/24p specifications.
* In SD mode, Time Code IN is not available if you select the 24F frame rate (the mode will be canceled and the
“TC-(IN OUT)” display on the side panel will disappear).
Connection Diagram
When synchronizing the camcorder to an external signal, input a reference video signal through the
GENLOCK terminal or a time code signal through the TIME CODE terminal. To input a time code signal
through the TIME CODE terminal, set the TIME CODE switch to IN. To output a time code signal, set the
switch to OUT.
* As a reference video signal input you can use either an HD Y signal or an NTSC composite video signal when recording
in HD.
*
Genlock ––
Time Code/User bit IN –––
Time Code OUT ––
Reference video
signal*
SMPTE-standard
LTC tim ing signal
GENLOCK
TIME CODE switch
TIME CODE
46


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Canon XHA1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Canon XHA1 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 8,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Canon XHA1

Canon XHA1 User Manual - German - 163 pages

Canon XHA1 User Manual - Dutch - 159 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info