615742
222
Zoom out
Zoom in
Previous page
1/246
Next page
Troubleshooting
222
Playback
Cannot delete MXF clips.
- You cannot delete MXF clips with an $ mark. Remove the $ mark (A 151) to delete the clip.
Deleting clips takes longer than usual.
- When the recording media contains a large number of clips, some operations may take longer than usual. Save your
clips (A 166) and initialize the recording media (A 41).
Cannot delete MP4 clips/photos.
- The LOCK switch on the SD card is set to prevent accidental erasure. Change the position of the LOCK switch.
- Photos that were protected using other devices cannot be deleted with the camcorder.
Cannot copy MXF clips.
- There is not enough available space on the CF card being copied to or the CF card already contains the maximum
number of clips (999 clips). Delete some clips (A 152) to free some space or replace the CF card.
Indicators and Onscreen Displays
ì appears in red on the screen.
- Battery pack is exhausted. Replace or charge the battery pack.
í appears on the screen.
- The camcorder cannot communicate with the battery pack attached so the remaining battery time cannot be
displayed.
The tally lamp does not illuminate.
- Set [Other Functions] > [Tally Lamp] > [Front] and/or [Rear] to [On].
The tally lamp flashes quickly. (4 flashes per second)
- The battery pack is exhausted. Replace or charge the battery pack.
- There is not enough available space on the recording media. Delete some clips (A 152) to free some space or replace
the recording media.
- A system error has occurred. Turn off the camcorder and back on again. If this does not solve the problem, consult a
Canon Service Center.
The tally lamp flashes slowly. (1 flash per second)
- The combined available space on both CF cards is low. Replace the CF card that is not being recorded onto.
- Available space on the SD card is low. Replace the SD card.
appears in red on the screen.
- An SD card error occurred. Remove and reinsert the SD card. If the display does not change back to normal, save your
MP4 clips (A 166) and photos and initialize the SD card (A 41).
Even after stopping recording, the CF card access indicator or SD card access indicator stays illuminated in red.
- The clip is being recorded. This is not a malfunction.
7 keeps flashing on the screen.
- You connected the optional GP-E2 GPS Receiver to the camcorders USB terminal in mode. Disconnect the
GP-E2 and connect in again after setting the camcorder in mode.
U keeps flashing on the screen.
- The camcorder cannot lock on the external Genlock signal being input. Check the external signal.
Picture and Sound
The OLED screen is too dark.
- Adjust the brightness with the [OLED/VF Setup] > [OLED Setup] > [Brightness] setting. To make the screen brighter
temporarily, set [OLED/VF Setup] > [OLED Setup] > [Luminence] to [On].
Screen displays turn on and off repeatedly.
- The battery pack is exhausted. Replace or charge the battery pack.
- Remove the battery pack and reattach it correctly.
Abnormal characters appear on the screen and the camcorder does not operate properly.
- Disconnect the power source and reconnect it after a short time. If the problem still persists, use the [Other Functions]
> [Reset] > [All Settings] function. This resets all the camcorder’s settings to default values except for the hour
meter.
COPY
222


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Canon XF200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Canon XF200 in the language / languages: English as an attachment in your email.

The manual is 23,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Canon XF200

Canon XF200 User Manual - German - 264 pages

Canon XF200 User Manual - Dutch - 248 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info