683291
152
Zoom out
Zoom in
Previous page
1/193
Next page
152
(2) [Exposure Compensation]
When [Auto], [Auto (Flickerless)] or [Auto (Shutter-
priority AE)] is selected for [Exposure], the exposure
compensation value desired can be selected from
nine levels (-4 to +4) using the slider.
To darken the image, select a negative value. To
brighten the image, select a positive value.
(3) [Metering Mode]
When [Auto], [Auto (Flickerless)] or [Auto (Shutter-
priority AE)] is selected for [Exposure], the metering
mode can be selected from [Center-Weighted],
[Average] or [Spot].
For an explanation on each item set in [Metering
Mode], see [Metering Mode] in the Setting page
(p. 54).
(4) [Shutter Speed]
When [Manual] or [Auto (Shutter-priority AE)] is
selected for [Exposure], select the shutter speed
desired. If [Manual] is selected, set the shutter speed
in the range of [1/1 sec] to [1/16000 sec] from a pull-
down menu. If [Auto (Shutter-priority AE)] is selected,
set the shutter speed in the range of [1/2 sec] to
[1/16000 sec] from a pull-down menu.
When capturing a moving subject, selecting a higher
shutter speed can reduce blurry video capture.
(5) [Slow Shutter]
You can set slow shutter if [Exposure] is set to [Auto]
or [Auto (Flickerless)]. Select a value in the range of
[1/2 sec] to [1/30 sec] from the pull-down menu.
As slower shutter speeds generate afterimages when
capturing a moving subject, select an appropriate
time according to the capture conditions.
(6) [Aperture]
If [Manual] is selected for [Exposure], set a desired
aperture value.
Moving the slider to the left closes the aperture and
darkens the image. Moving the slider to the right
opens the aperture and brightens the image.
(7) [Gain]
If [Manual] is selected for [Exposure], set a desired
gain value.
Moving the slider to the left decreases the gain
(sensitivity to brightness) and darkens the image.
Moving the slider to the right increases the gain and
brightens the image.
Setting White Balance
(1) [Auto]
The white balance is adjusted automatically.
(2) [Light Source]
Select the light source from the pull-down menu below
according to the condition in which the camera is
used.
For an explanation on each item set in [Light Source],
see [White Balance] in the Setting page (p. 55).
(3) [Manual]
The white balance is adjusted manually.
[One-shot WB]
This is used for forcibly locking the white balance to
match the light source.
Important
If the subject is a traffic signal or electronic scoreboard, etc.,
the captured image may flicker.
In this case, try changing [Exposure] to [Auto (Shutter-priority
AE)] and then select a shutter speed lower than 1/100, to see
if the situation improves.
[Exposure Compensation] and [Manual] for [Exposure]
cannot be selected if [Smart Shade Control] is set to [Auto].
When [Camera] > [Camera Control] > [AGC Limit] is set to
[OFF] in the setting page and [Exposure] is set to [Auto
(Shutter-priority AE)], exposure compensation and backlight
compensation will not be performed.
(1)
(2)
(3)
(3)
152


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Canon VB-H730F at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Canon VB-H730F in the language / languages: English as an attachment in your email.

The manual is 8,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info