809437
102
Zoom out
Zoom in
Previous page
1/254
Next page
Setting the Time Code
102
Selecting Drop or Non-Drop Frame
When the frame rate is set to 59.94P, 59.94i or 29.97P, you can select between a drop frame (DF) or non-drop
frame (NDF) time code, depending on how you plan to use your recordings.
With all other frame rates, the time code is set to non-drop frame (NDF) and cannot be changed.
Select > [
B
System Setup] > [Time Code DF/NDF] > Desired option.
The time code display will change depending on the setting. When you select [DF], the time code will appear
as [00:00:00.00]; when you select [NDF], it will appear as [00:00:00:00].
About the time code display
A letter may appear next to the time code depending on the setting/status. Refer to the following table.
NOTES
NOTES
The frames value of the time code runs from 0 to 23 (frame rate set to 23.98P or 24.00P), from 0 to 24 (frame
rate set to 25.00P, 50.00i or 50.00P), or from 0 to 29 (all other frame rates).
When slow & fast motion recording/frame recording/interval recording is activated, you cannot select the [Free
Run] running mode. Conversely, when pre-recording is activated, [Free Run] is set automatically and cannot be
changed.
When slow & fast motion recording/frame recording/interval recording is activated, the time code signal will not
be output from any of the terminals.
When you mix drop frame and non-drop frame time codes, there might be a discontinuity in the time code at
the point where the recording starts.
When you are using the [Free Run] running mode, the time code will continue running as long as the built-in
backup battery has some charge left, even if you disconnect all other power sources.
If you set an assignable button to [Time Code] (A125), you can press the button to open the
[B System Setup] menu page with the time code settings.
Setting the User Bit
You can set a user bit composed of the date or the time of recording or an identification code consisting of
8 characters in the hexadecimal system. There are sixteen possible characters: the numbers 0 to 9 and the
letters A to F.
The user bit is recorded with clips and can be output from the TIME CODE terminal/HDMI OUT terminal. It can
be used freely to categorize and manage recordings or to keep additional information about them.
1Select > [
B
System Setup] > [User Bit Type] > [Setting], [Date] or [Time].
If you select [Time] or [Date] the rest of the procedure is not necessary.
2Select [Change].
To reset the user bit to [00 00 00 00], select [Reset] instead.
3 Enter the user bit using the data entry screen (A25).
Letter Description
RThe time code mode is set to [Regen.].
PThe time code mode is set to [Preset] and the running mode is set to [Rec Run].
FThe time code mode is set to [Preset] and the running mode is set to [Free Run].
EThe time code signal is coming from an external source.
No letter Time code during clip playback.
102


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Canon EOS R5 C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Canon EOS R5 C in the language / languages: English as an attachment in your email.

The manual is 13.28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Canon EOS R5 C

Canon EOS R5 C User Manual - English - 797 pages

Canon EOS R5 C User Manual - German - 263 pages

Canon EOS R5 C User Manual - German - 815 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info