624614
27
Zoom out
Zoom in
Previous page
1/106
Next page
24 25
PART I
(3) On a derailleur gear system, pull the derailleur
body back with your right hand.
(4) With a cam action mechanism, move the quick-
release lever to the OPEN position (fig. 8b). With
a through bolt or bolt on mechanism, loosen the
fastener(s) with an appropriate wrench, lock lever
or integral lever; then push the wheel forward far
enough to be able to remove the chain from the
rear sprocket.
(5) Lift the rear wheel o the ground a few inches
and remove it from the rear dropouts.
d. Installing a disk brake or rim brake rear
wheel
CAUTION
If your bike is equipped with a rear disk brake,
be careful not to damage the disk, caliper or
brake pads when re-inserting the disk into the
caliper. Never activate a disk brake’s control lever
unless the disk is correctly inserted in the caliper.
(1) With a cam action system, move the cam lever
to the OPEN position (see fig. 8 a & b). The lever
should be on the side of the wheel opposite the
derailleur and freewheel sprockets.
(2) On a derailleur bike, make sure that the rear
derailleur is still in its outermost, high gear,
position; then pull the derailleur body back with
your right hand. Put the chain on top of the
smallest freewheel sprocket.
(3) On single-speed, remove the chain from the
front sprocket, so that you have plenty of slack
in the chain. Put the chain on the rear wheel
sprocket.
(4) Then, insert the wheel into the frame dropouts
and pull it all the way in to the dropouts.
(5) On a single speed or an internal gear hub, replace
the chain on the chainring; pull the wheel back
in the dropouts so that it is straight in the frame
and the chain has about 1/4 inches of up-and-
down play.
(6) With a cam action system, move the cam lever
upwards and swing it into the CLOSED position
(fig. 8 a & b). The lever should now be parallel
to the seat stay or chain stay and curved toward
the wheel. To apply enough clamping force, you
should have to wrap your fingers around the
seat stay or chainstay for leverage, and the lever
should leave a clear imprint in the palm of your
hand.
(7) With a through-bolt or bolt-on system, tighten
the fasteners to the torque specifications
in PART II “Tightening Torques” or the hub
manufacturer’s instructions.
NOTE:
If, on a traditional cam action system, the lever
cannot be pushed all the way to a position
parallel to the seat stay or chain stay, return the
lever to the OPEN position. Then turn the tension
adjusting nut counterclockwise one-quarter turn
and try tightening the lever again.
WARNING
SECURELY CLAMPING THE WHEEL WITH
A CAM ACTION RETENTION DEVICE TAKES
CONSIDERABLE FORCE.
If you can fully close the cam lever without
wrapping your fingers around the seat stay or
chain stay for leverage, the lever does not leave
a clear imprint in the palm of your hand, and the
serrations on the wheel fastener do not emboss
the surfaces of the dropouts, the tension is
insucient. Open the lever; turn the tension
adjusting nut clockwise a quarter turn; then try
again.
See also WARNING on page 20.
(continued on next page...)
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cannondale 2011 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cannondale 2011 in the language / languages: English as an attachment in your email.

The manual is 3,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Cannondale 2011

Cannondale 2011 User Manual - German - 104 pages

Cannondale 2011 User Manual - Dutch - 104 pages

Cannondale 2011 User Manual - French - 104 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info