764896

Canadian Spa Company Vancouver KH-10032 Manual

8
Zoom out
Zoom in
Previous page
1/24
Next page
VANCOUVER
Filling up your Spa
IMPORTANT: Before lling the spa, it is important to read and
understand the water chemistry section of this manual. Do not
proceed until the water chemistry section is understood and the
source water is tested.
Verify that the spa is in the desired nal location. Refer to the
‘Choose your location’ section - once lled, the spa cannot be
moved without draining.
Follow these lling instructions to avoid damage to the spa
pumps:
1. Leave power to the spa off until spa is completely lled.
2. Never leave an unlled spa exposed to direct sunlight with
out the Spa Cover installed. Resulting damage such as
bubbles and wrinkles in the spa shell and fading of the jet
faces is not covered by the manufacturer’s warranty.
3. Never operate spa pump without water because this could
result in permanent pump and/or heater damage which is
not covered by the manufacturer’s warranty.
4. Remove all warning labels from spa shell.
6. Remove the lter lid, basket and lter cartridge.
7. Inspect all Jets (shipping may cause jets to become loose
or detached). Check to see that the black Drain Valve
(located to the left or right of the front access panel) is closed.
IMPORTANT: Follow the next steps closely to prevent damage
to the Spa Pump.
Filter Type: Glacier Microban Filter Set SKU: KA-10032
8. Insert garden hose or other clean water source directly into
lter housing. Push hose pipe into lter housing until it
stops. Fill up to middle of the skimmer. Secure hose
placement and turn on water. Filling the spa through the
lter housing prevents an air lock from occurring in the spa
pumps, which is an air pocket preventing the ow of
water through the pump. Permanent damage caused by
running the pump with an air lock (or without water) is not
covered by the manufacturer’s warranty.
9. Check for leaks! Although spas are fully checked at the
factory, shipping and delivery might cause a leak.
10. Before power is applied familiarise yourself with the spa
control operations.
11. Turn water off and remove hose.
12. Reinstall lter cartridge, basket and lter lid.
13. Add start-up Chemicals after power is turned on.
Draining your Spa/Using the drain valve
1. Start by shutting off the electrical breaker connected to
your spa.
2. Locate the drain valve at the side of the spa. This valve has
a straightforward locking mechanism that stops the water
from owing out while you attach a garden hose to the cap.
First using the tab of the cap pull and twist until the pipe
comes out.
Then with the pipe out turn clockwise until the pipe extends
further out.
3. With the valve fully extended, unscrew the cap from the
middle of the valve.
4. Screw in the male end of the garden hose to the valve and
run the hose to your drain location.
5. Once the water has stopped owing out of the drain valve,
use the wet/dry vacuum to suck out any remaining water
from each jet head.
6. Twist valve and push in to CLOSE.
Accessing your spa controls
(8)
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Canadian Spa Company Vancouver KH-10032 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Canadian Spa Company Vancouver KH-10032 in the language / languages: English as an attachment in your email.

The manual is 1,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info