801016

Camry CR 4011 Manual

6
Zoom out
Zoom in
Previous page
1/116
Next page
6
12. The power cord must not hang over the edge of the table or touch hot
surfaces.
13. Do not leave the device or the power supply in the socket unattended
when it is switched on.
14. For additional protection, it is advisable to install a residual current
device (RCD) in the electrical circuit with a rated residual current not
exceeding 30 mA . A specialist electrician should be consulted in this
regard.
15. Before turning on the device, make sure that all parts are properly
installed.
16. Use only accessories provided by the manufacturer.
17. Be careful not to overload the machine , do not exceed the top edge
of the grain hopper (1) .
18. Always disconnect the device from the mains and disconnect the
power cord from the device when it is not in use or you want to start
cleaning it.
19. Do not disassemble the juicer while it is connected to a power socket.
20. Do not use abrasive pads or aggressive cleaning agents for cleaning.
21. After use and the device heater has cooled down, it is recommended
to disassemble and wash the elements thoroughly.
22. The device includes a heating element to facilitate
drainage of the oil and to obtain more of it. After finishing
work, wait approx. 20 minutes for the heater to cool down
and only after that time you can dismantle it, clean it from
seed residues and wash the device.
23. The maximum operating time of the device is 45 minutes. After this
time, the device turns off to protect the engine from overheating and
damage. Wait 20 minutes before restarting the device.
24. The device is used for extracting oil from oil plants : nuts, seeds,
seeds and grains , the oil content of which is greater than 30% . It is
forbidden to use the device with olives, olive pits , soybeans , vegetables ,
fruits, mushrooms .
1. Hopper
Device Description:
2. Cover lid
3. Filter
4. Socket
5. Keypad
6. Hopper cover
7. Pressing chamber cover and heating unit
8. Oil Container
9. Pomace container
10. Pressing chamber buckle
11. Outside cover lid
12. Pressing shaft
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Camry CR 4011 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Camry CR 4011 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish as an attachment in your email.

The manual is 3.4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info