662467
10
Zoom out
Zoom in
Previous page
1/92
Next page
2) Open the gas cylinder valve.
3) Press the control knob and turn it to the full flame
( ) position, then immediately press the igniter
button ( ) until you hear the click. Repeat 3 or 4
times if necessary until the burner is lit.
4) If the burner fails to light, turn the control knob to the
"off" position (O). Wait 5 minutes before repeating the
operation.
Important:
If the burner fails to light after the 2
nd
attempt, turn the
control knob to the "off" position (O) and check that the
burner outlets and the venturi tube are not blocked.
i) Lighting manually the burner
If Piezo ignition does not work, put the adjustment lever
in the "OFF" (O) position. Remove the drippings tray
located under the vat. Hold a lighted match to the
opening located under the burner, then open the lever on
the control panel to full-flow position ( ). Reposition the
drippings tray.
j) Turning off the grill burner
Return the control knobs to the "off" position (O), then
close the cylinder valve.
k) Operation
1. It's recommended that protective gloves be worn to
handle components which may be very hot.
2. Before start-up, put the feet in place (see paragraph c),
then open the fold-down shelves:
r Unfold the two shelf-support wires.
r Open the shelves until they are resting on the shelf-
support wires.
Flexible tubing connection: To connect the tubing to the
connector on the barbecue, tighten the nut on the tubing
firmly but without excess force using the two wrenches
provided:
- no. 11 wrench to tighten the connector
- no. 17 wrench to tighten the nut on the tubing
f) Checking for gas leaks
1) Work outside, away from all sources of ignition. Do not
smoke.
2) Make sure the control knob is in the "off" (O) position.
3) Push the end of the hose completely onto the regulator
nozzle and secure with a suitable clip.
4) Fit the regulator onto the gas cylinder in accordance
with its instructions.
5) Use a gas leak solution to test for leaks. Important:
never use a naked flame to check for gas leaks.
6) Apply the solution to the connections cylinder/regulator/
hose/apparatus (the control knobs should remain
closed: off position). Open the gas cylinder valve.
7) Bubbles in the gas leak solution indicate that there are
gas leaks.
8) The leak can be stopped by tightening any hose
connection or replacing any faulty component. The
barbecue must not be used until the leak is stopped.
9) Close the valve on the gas cylinder. Check for leaks at
least once per year and each time the gas cylinder is
replaced.
g) Prior to use
Never use the barbecue until the instructions have been
read carefully and understood. Also, make certain that:
- there are no leaks
- the venturi tubes are not blocked
- the hose does not touch any components which may get hot.
- that the feet are unfold (see paragraph K) 2.).
h) Lighting the burner
Read steps 1 to 5 before beginning with step 1.
1) Make sure the control knob is in the "off" (O) position.
10
Fargo
burner tube
burner outlets
O
GB
11
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Campingaz Fargo at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Campingaz Fargo in the language / languages: All languages as an attachment in your email.

The manual is 1,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info