590633
8
Zoom out
Zoom in
Previous page
1/66
Next page
8/66 Device handbook CAM mobile, 06/2014
4 Preparation of measurement application
Before performing measurements the CAM mobile must be configured for the measurement application via the
USB interface, because via display no such settings can be performed. To do so, the device must be supplied
with power. The subsequent described parameterization is done using the CB-Manager software.
4.1 Installation of the CB-Manager Software
The installation of the CB-Manager software is described in detail in the fileRead-me-first.pdfon the supplied
CD and is as well shown in Appendix D1
. After starting the application Setup.exe“ in the directory „Software
CB-Manager Vxxx“ the CB-Manager and the USB driver will be installed. The USB driver is required for the
later communication with the device.
4.2 Connecting CAM mobile to PC
Observe warning 1 of the safety precautions
Connect the device to an applicable power supply by means of the IEC power cord and switch the device on.
Then connect the USB connector of the CAM mobile to a USB connector of the PC.
4.3 Parameterization of the CAM mobile
After the first start-up of the software set the communication interface to „USB“ using the menu item options |
interface. Once done use system | search devices to bring the CAM mobile into the device list. By double-
clicking on the appropriate symbol in the device list the present parameterization of the device is read and
displayed.
For configuration parameters a context-sensitive help is available in the CB-Manager,
which describes the meaning of the specific settings. To display just right-click with the
mouse on the corresponding input field.
4.3.1 Parameterization of the measurement input
In the register „inputthe features of the system to monitor can be defined. Along with the system type
expectations of the maximum signal levels must be defined, i.e. the maximum overriding of the voltage and
current quantities which should still be measurable.
The configuration of the current inputs has to match the setting of
the rotary-switch of the Rogowski coils. The coils support the following three
ranges:
Range Sensitivity per [A]
30A 100mV
300A 10mV
3000A 1mV
Example: You want to measure max. 200 A with 10% over range
Current input: prim. 200A / sec. 2V
Position of rotary-switch: 300 A
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Camille Bauer SINEAX CAM mobile at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Camille Bauer SINEAX CAM mobile in the language / languages: English as an attachment in your email.

The manual is 8,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info