168721
8
Zoom out
Zoom in
Previous page
1/18
Next page
Switching on/off the unit
Switch on the unit by pressing any button
(except button and button) or inserting
a disc to disc slot.
When system is on, press the button to
turn off the unit.
Sound adjustment
- Rotate the volume knob on the head unit to
adjust volume level.
- Press the button to enter into the
audio selecting mode. Press this button
continually will change in the following
order:
SEL
When TP information gets lost at the
current station for retune time, the beep
sound is out-putted.
When newly tuned station has not RDS
signal, “PI SEEK” is suppressed somewhat.
Rotate the volume knob button to adjust the
desired sound quality.
-for2
seconds to enter into the menu mode
Press it continually, it is activated as
cyclical mode of following functions for
user's selection
Press and hold the button
Rotate the volume knob to select the
desired item.
SEL
.
:
TA SEEK/ALARM PI SOUND/MUTE RETUNE L/S
MASK DPI/ALL BEEP 2’ND/ALL/OFF
VOL BAS TRE BAL FAD
(Volume) (Bass) (Treble) (Balance) (Fader)
TA SEEK/ALARM
- TA SEEK mode:
- TA ALARM mode:
When newly tuned station does not
receive TP information for a few seconds,
the radio retunes to next station which has
not the same station (PI) as the last station,
but has the TP information.
When TP information gets lost at the
current station for retune time which is set
by RETUNE SHORT (30 sec.) or RETUNE
LONG (90 sec.), the radio start to retune to
next same PI station. When same PI station
does not catch in 1 cyclic search, the radio
retunes to next station with TP information.
When this mode is selected, any
automatic retune mode is not activated.
Only double beep sound (ALARM) is
output.
When newly tuned station does not have
TP information for several seconds, beeps
come out.
PI SOUND/MUTE
While AF switching is implemented in
C201 station, AF can switch to 100 MHz,
which is non genuine AF (where, different PI
with same AF) in short “DIP”.
If a car cruises that critical area back and
forth, an oscillation phenomenon can be
occurred, because the different PI code can
be received from 100 MHz with “XXX” PI.
The car radio has special procedure to
reduce even this kind of unavoidable
situation however there is a limit to be
escaped from this serious case perfectly.
In that serious case, 2 modes are
selectable as follows:
The AF frequency (which has different PI
or NO RDS signal with high field strength) is
masked during checking PI when the unit
-PISOUNDmode:
-PIMUTEmode:
- RETUNE L mode:
- RETUNE S mode:
When above different PI sound (DIP) is
heard once in a while, the Dip's sound will
be heard for a short time.
Under above same situation, a mute
sound will be heard for a short time.
The initial time of automatic TA search or
PI search modes is selected.
When PI information is not caught for
retune time, the radio starts to retune to
next same PI station.
When same PI station does not catch 1
cyclic search, the radio goes to last station
and waits for several minutes until PI code
is received.
Selected as 90 seconds.
Selected as 30 seconds.
RETUNE L/S
MASK DPI /ALL
General Operations
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Caliber mcd 163 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Caliber mcd 163 in the language / languages: English as an attachment in your email.

The manual is 0,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Caliber mcd 163

Caliber mcd 163 Quick start guide - English, German, Dutch, French, Italian, Polish, Portuguese, Swedish, Spanish - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info