784912
10
Zoom out
Zoom in
Previous page
1/44
Next page
Page 7
Getting Started
2. AFTER THE SPA HAS BEEN FILLED with water and the
equipment compartment door is secured, power must be applied to
the spa.
FIRST activate power to the subpanel from the main house panel.
NEXT open the door of the electrical subpanel and reset the
GFCI/RCD breaker.
FINALLY, close and secure the subpanel door.
3. TO CHECK THE OPERATION OF THE JET SYSTEM and to purge
any remaining air from the heating system complete the following
steps:
Press the
JETS
OFF
OFF
OFF
1
2
3
icon on the Jet screen for each pump to place
the jet pumps on High.
Once the jet system is fully operational (as indicated by strong,
non-surging jets), priming of the spa is complete
To turn off the jets, press
the on the jet screen
to turn all
functions off simultaneously.
If you do not feel a steady stream of water from your jets,
refer to the instructions for priming the pump in the SPA
TROUBLESHOOTING section.
IMPORTANT: Be sure that the diverter is in the middle position.
4. SET THE TEMPERATURE CONTROL to the desired temperature
between 38°C and 40°C, then place the spa cover on the spa and
allow the water temperature to stabilize (approximately 24 hours).
Make sure you secure the cover in place using the cover locks.
Periodically check the spa water temperature. When the water
temperature climbs above 32°C, proceed to the next step. The spa
temperature is pre-programmed to reach 39°C, and will normally do
so within 18 to 24 hours. You may change the water temperature by
pressing the temperature on the home screen, then press the
on
the screen to raise the temperature, or ▼ to lower the temperature.
After a few hours, the water temperature will remain within 1.5°C of
your selected temperature.
5. USING A TEST STRIP AND APPLICABLE CHEMICALS adjust
Total Alkalinity (TA) to 40-120 ppm, Calcium Hardness between
75-150 ppm, then spa water pH to between 7.2 and 7.8. These
procedures are listed in the “Water Quality and Maintenance”
section.
OPERATION NOTE: Adjusting the Total Alkalinity as the first step is
important, as out-of balance TA will affect your ability to adjust the pH
correctly and will prevent the sanitizer from operating effectively.
When using the FRESHWATER Salt system the Calcium Hardness
must be between 25 - 75 ppm, if hardness is above 75 ppm use
VANISHING ACT (see pg. 11).
IMPORTANT: Activate the Clean cycle (Press on the home
screen then Start) before adding spa water chemicals directly into
the filter compartment. Make sure all diverter valves are set to the
middle position.
6. SUPERCHLORINATE THE SPA WATER by adding 1½ teaspoons
of chlorine (sodium dichlor) per 950 liters of spa water, then activate
the Clean cycle.
7. TEST THE SPA WATER FOR CHLORINE RESIDUAL. If the
residual is between 3 and 5 ppm on the test strips, go on to the next
step. If the residual is less than 3 ppm, activate the Clean cycle, add
chlorine as needed and then retest.
WARNING: High sanitizer levels can cause discomfort to the user’s
eyes, lungs and s kin. Always allow the sanitizer level to fall to the
recommended range before using the spa.
8. RECHECK the Total Alkalinity (TA) 40-120 ppm, Calcium Hardness
between 75-150 ppm, then spa water pH between 7.2 and 7.8.
OPERATION NOTE: Make sure you adjust your Total Alkalinity and
pH correctly, this will affect
the sanitizers effectiveness.
The spa is ready for use when the spa water has circulated and the
bromine level remains between 1 and 2 ppm or chlorine level remains
between 3 and 5 ppm.
OPERATION NOTE: For proper water circulation during the ten-minute
Clean cycle the following steps should be performed.
Place the diverter valve in the middle (split flow) position
Place air control levers in OFF position by rotating clockwise
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Caldera Utopia - serie 2019 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Caldera Utopia - serie 2019 in the language / languages: English as an attachment in your email.

The manual is 10.12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Caldera Utopia - serie 2019

Caldera Utopia - serie 2019 User Manual - German - 44 pages

Caldera Utopia - serie 2019 User Manual - Dutch - 44 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info