784914
10
Zoom out
Zoom in
Previous page
1/44
Next page
Page 7
Getting Started
4. SET THE TEMPERATURE CONTROL to the desired temperature
between 38°C (100°F) and 40°C (104°F), then place the spa
cover on the spa and allow the water temperature to stabilize
(approximately 24 hours). Make sure you secure the cover in place
using the cover locks. Periodically check the spa water temperature.
When the water temperature climbs above 32°C (90°F), proceed
to the next step. The spa temperature is pre-programmed to reach
38°C (100°F), and will normally do so within 18 to 24 hours. You may
change the water temperature by pressing the OPTION hard button
then press the soft button next to Temperature, (press soft button
next to
on the control panel to raise the temperature, or lower
temperature by pressing soft button next to ▼). After a few hours,
the water temperature will remain within 1.5°C (3°F ) of your selected
temperature.
5. USING A TEST STRIP AND APPLICABLE CHEMICALS adjust
Total Alkalinity (TA) to 80 ppm, Calcium Hardness (CH) between
75 - 150 ppm (if using Salt System between 25 - 75 ppm), then
spa water pH to between 7.4 and 7.8. These procedures are listed in
the “Water Quality and Maintenance” section.
OPERATION NOTE: Adjusting the Total Alkalinity as the first step is
important, as out-of balance TA will affect your ability to adjust the pH
correctly and will prevent the sanitizer from operating effectively.
When using the FRESHWATER Salt system the Calcium Hardness
must be between 25 - 75 ppm, if hardness is above 75 ppm use
VANISHING ACT (see pg. 11).
IMPORTANT: Activate the Clean cycle (Press the soft button next
to CLEAN on the home screen) before adding spa water chemicals
directly into the filter compartment. Make sure all diverter valves are
set to the middle position.
6. SUPERCHLORINATE THE SPA WATER by adding 1½ teaspoons
of FRESHWATER chlorine (sodium dichlor) per 950 liters (250
gallons) of spa water, then activate the Clean cycle.
7. TEST THE SPA WATER FOR CHLORINE RESIDUAL. If the
residual is between 1 and 5 ppm on the test strips, go on to the next
step. If the residual is less than 1 ppm, activate the Clean cycle, and
then retest, add more chlorine as necessary.
WARNING: High sanitizer levels can cause discomfort to the user’s
eyes, lungs and skin. Always allow the sanitizer level to fall to the
recommended range before using the spa.
8. RECHECK the Total Alkalinity (TA) 40 - 120 ppm, Calcium
Hardness (CH) 75 - 150 ppm (25 - 75 ppm with salt), then spa water
pH between 7.2 and 7.8.
OPERATION NOTE: Make sure you adjust your Total Alkalinity and
pH correctly, this will affect
the sanitizers effectiveness.
The spa is ready for use when the spa water has circulated and
the chlorine level remains between 1 and 5 ppm.
OPERATION NOTE: For proper water circulation during the ten-minute
Clean cycle the following steps should be performed.
Place the diverter valve in the middle (split flow) position
Place air control levers in OFF position by rotating clockwise
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Caldera Paradise - serie 2022 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Caldera Paradise - serie 2022 in the language / languages: English as an attachment in your email.

The manual is 6.53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Caldera Paradise - serie 2022

Caldera Paradise - serie 2022 User Manual - German - 44 pages

Caldera Paradise - serie 2022 User Manual - Dutch - 44 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info