Manual Cadac Carri Chef 50 - 8910 (page 5 of 160) (English, German, Dutch, Danish, French, Italian, Polish, Swedish, Turkish, Spanish, Norwegian, Finnish)

819977

Zoom out

Zoom in

1/160

2. Fitting and Changing the Gas Supply

Connecting the gas supply

• Before connecting the appliance to a gas supply, ensure that the rubber seal on the regulator is in position

and in good condition.

• Before connecting the hose and regulator to the appliance, check that the appliance control knob is in the

“OFF” position.

• Carry out this check each time you ﬁt the appliance to a gas cylinder.

• Blow out any dust from the gas supply opening to prevent possible blockage of the jet.

• NOTE! When installing the tailpiece, ensure it is held straight while tightening the tailpiece nut, in order to

prevent a possible gas leak. Tighten with a suitable spanner or hand wheel (Fig. 2a).

• Fit an approved hose and regulator to the appliance.

• Ensure that the gas supply (gas cylinder/gas cartridge) is ﬁtted in a well-ventilated location away from any

source of ignition, such as naked ﬂames and away from other people.

• Do not twist or pinch the hose. Ensure that it is routed away from the stove body so as to prevent

deterioration / damage to the hose caused by heat.

• Make sure that the gas cylinder is kept upright at all times, connect to the cylinder by screwing on hand tight

until fully engaged.

• Ensure that a complete gas seal has been made (check for the smell of gas around the connection joint). Do

not check for leaks with a naked ﬂame. Use warm soapy water only, applied to the joints and connections of

the appliance. Any leakage will show up as bubbles around the leakage area.

• If you cannot rectify the gas leak do not use the appliance. If you are in doubt, contact your nearest

stockist.

Disconnecting and changing the gas supply

• Aer use, turn the appliance control knob to the “OFF” position and close the gas supply.

• When you need to replace your empty cylinder, make sure that the gas is closed at the cylinder

valve.

• Do not smoke while changing the cylinder.

• Remove the regulator from the empty cylinder.

• Attach the regulator to the full cylinder, refer to the instructions above on how to connect the gas

supply.

• Apply the same care and checking procedures as if ﬁtting a new gas cylinder.

How to check if your gas cylinder is empty

• The easiest way to check if you are low on gas is by picking up your gas cylinder.

• If you think your gas cylinder is feeling a little lighter than you’d like, weighing the bottle is a great way to see how much gas is le. Most

cylinders will have the empty weight stamped on either the neck or foot ring, and if the weight indicated on the stamp and the weight of your

cylinder are the same, you’re out of gas. You can then approximate the amount of gas you have le by the diﬀerence in weight.

3. Operating the Appliance

Assembly and use

• The appliance is designed to be portable, therefore the legs and the utility tray are easily removable and dis-assemble for the ease of transport

and use.

• User assembly / dis-assembly is limited to the ﬁtment of the legs, utility tray and the installation / removal of cooking surfaces.

• When assembling the legs, always make sure that the leg securing rings have been securely fastened and that the assembled product is stable

and does not rock. Do not use the appliance without ﬁtting the utility tray as it also plays an important role in ensuring the overall sturdiness of

the appliance.

• Should the heat shield, fat pan or burner pan become damaged in such a way that permanent contact between the heat shield and the fat pan

occurs during use, do not use the appliance. Return it to your stockist for repair.

• Do not cover up or change the air holes in the valve box cover as this will aﬀect the performance of the product and may lead to an unstable

ﬂame.

• When operating this appliance, please take care to ensure that all parts are in good working order and that you have checked for any gas

leaks before lighting the appliance with every use.

• Cooking surfaces can simply be placed and are ready to use. No assembly required.

• PLEASE NOTE: Please ensure all protective packaging and plastic are removed from the appliance before use.

• The appliance is designed for use with cooking vessels of not less than 225mm diameter and not greater than 450mm in diameter.

Precautions to observe before lighting.

• Use this appliance only on a ﬁrm level surface.

• Aer prolonged storage, inspect the appliance for any insects and webs, which may aﬀect gas ﬂow.

Using the control knob

The control knob is ﬁtted with two positive stop positions, one at low, and one at ignite/high. This limits the adjustment of the ﬂame to

between these two points.

Fig. 2b

Fig. 2a

Hand

wheel

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Cadac Carri Chef 50 - 8910 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5.76 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Cadac Carri Chef 50 - 8910 Manual

Product: