632544
13
Zoom out
Zoom in
Previous page
1/24
Next page
OWNER’S INSTRUCTION & SAFETY MANUAL10
BURLEY.COM
Figure 8
Figure 9
Hooking up Your Trailer
1. Installing the hitch to your bike: Remove
quick-release or nut from the left side of bike’s rear
wheel axle. Install hitch between quick-release or nut and
frame (Figure 8). Tighten the quick-release or nut follow-
ing manufacturer’s recommendation. The
hitch can remain on the bike when trailer
is removed.
2. Hooking the tow bar to the hitch: Insert flex con-
nector in between the two holes on the hitch. Insert lock
pin and close retainer.
Wrap safety strap around the frame of the bike twice and
latch to the D-ring on the
tow bar (Figure 9).
Accrochage de votre remorque
1. Installation de l’attelage sur votre vélo : Retirez
le levier de blocage rapide ou l’écrou du côté gauche de
l’axe de la roue arrière du vélo. Installez l’attelage entre le
levier de blocage rapide ou l’écrou et le cadre (Figure 8).
Serrez le levier de blocage rapide ou l’écrou en suivant les
recommandations du fabricant. L’attelage peut rester sur
le vélo lorsque la remorque n’est pas accrochée.
2. Accrochage de la barre de remorquage à
l’attelage : Insérez le raccord souple entre les deux trous
sur l’attelage. Insérez la goupille de sécurité et fermez le
dispositif de retenue. Enroulez la sangle de sécurité autour
du cadre du vélo deux fois et accrochez-la à l’anneau d’ar-
rimage sur la barre de remorquage (Figure 9).
Conexión de su remolque
1. Colocación del enganche en la bicicleta:
quite la liberación rápida o la tuerca del lado izquierdo
del eje de la rueda trasera de la bicicleta. Instale el
enganche entre la liberación rápida o la tuerca y el
marco (figura 8). Apriete la liberación rápida o la tuer-
ca de acuerdo con la recomendación del fabricante. El
enganche puede permanecer en la bicicleta cuando se
quita el remolque.
2. Colocación de la barra de remolque en el
enganche: inserte el conectador flexible entre los dos
orificios del enganche. Inserte el pasador de bloqueo y
cierre el retén. Envuelva la correa de seguridad alred-
edor del marco de la bicicleta dos veces y engánchela
al anillo en forma de D de la barra de remolque (figura
9).
Ankoppeln Ihres Anhängers
1. Montage der Anhängerkupplung an Ihrem
Fahrrad: Entfernen Sie den Schnellverschluss oder
die Mutter von der linken Seite der hinteren Radachse
des Fahrrads. Montieren Sie die Anhängerkupplung
zwischen dem Schnellverschluss oder der Mutter und
dem Rahmen (Abbildung 8). Ziehen Sie den Schnell-
verschluss oder die Mutter gemäß den Empfehlungen
des Herstellers fest. Die Anhängerkupplung kann
am Fahrrad verbleiben, wenn der Anhänger entfernt
wurde.
2. Ankoppeln der Zugstange an der Anhängerk-
upplung: Stecken Sie das flexible Verbindungsstück
zwischen die beiden Löcher der Anhängerkupplung.
Stecken Sie den Sicherungsstift hinein und schließen
Sie die Arretierung. Wickeln Sie den Sicherungsriemen
zweimal um den Fahrradrahmen und befestigen Sie
ihn an der Öse an der Zugstange (Abbildung 9).
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Burley Tail Wagon 2015 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Burley Tail Wagon 2015 in the language / languages: English, German, French, Spanish as an attachment in your email.

The manual is 2,83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info