632448

Burley D-Lite 2015 Manual

18
Zoom out
Zoom in
Previous page
1/26
Next page
Hooking up Your Trailer
1. Installing the hitch to your bike: Remove
quick-release or nut from the left side of
bike’s rear wheel axle. Install hitch between
quick-release or nut and frame (Figure 18).
Tighten the quick-release or nut following
manufacturer’s recommendation. The
hitch can remain on the bike when trailer
is removed.
2. Hooking the tow bar to the hitch: Insert flex
connector in between the two holes on the
hitch. Insert lock pin and close retainer.
Wrap safety strap around the frame of the
bike twice and latch to the D-ring on the
tow bar (Figure 19).
Figure 18
Figure 19
Accrochage de votre remorque
1. Installation de l’attelage sur votre vélo : Retirez
le levier de blocage rapide ou l’écrou du côté
gauche de l’axe de la roue arrière du vélo. Installez
l’attelage entre le levier de blocage rapide ou l’écrou
et le cadre (Figure 18). Serrez le levier de blocage
rapide ou l’écrou en suivant les recommandations
du fabricant. L’attelage peut rester sur le vélo
lorsque la remorque n’est pas accrochée.
2. Accrochage de la barre de remorquage à l’attelage
: Insérez le raccord souple entre les deux trous
sur l’attelage. Insérez la goupille de sécurité et
fermez le dispositif de retenue. Enroulez la sangle
de sécurité autour du cadre du vélo deux fois et
accrochez-la à l’anneau d’arrimage sur la barre de
remorquage (Figure 19).
Conexión de su remolque
1. Colocación del enganche en la bicicleta: quite la
liberación rápida o la tuerca del lado izquierdo
del eje de la rueda trasera de la bicicleta.
Instale el enganche entre la liberación rápida
o la tuerca y el marco (figura 18). Apriete la
liberación rápida o la tuerca de acuerdo con
la recomendación del fabricante. El enganche
puede permanecer en la bicicleta cuando se
quita el remolque.
2. Colocación de la barra de remolque en el
enganche: inserte el conectador flexible entre
los dos orificios del enganche. Inserte el pasador
de bloqueo y cierre el retén. Envuelva la correa
de seguridad alrededor del marco de la bicicleta
dos veces y engánchela al anillo en forma de D
de la barra de remolque (figura 19).
Ankoppeln Ihres Anhängers
1. Montage der Anhängerkupplung an Ihrem Fahrrad:
Entfernen Sie den Schnellverschluss oder die Mutter
von der linken Seite der hinteren Radachse des
Fahrrads. Montieren Sie die Anhängerkupplung
zwischen dem Schnellverschluss oder der Mutter
und dem Rahmen (Abbildung 18). Ziehen Sie
den Schnellverschluss oder die Mutter gemäß
den Empfehlungen des Herstellers fest. Die
Anhängerkupplung kann am Fahrrad verbleiben, wenn
der Anhänger entfernt wurde.
2. Ankoppeln der Zugstange an der Anhängerkupplung:
Stecken Sie das flexible Verbindungsstück zwischen
die beiden Löcher der Anhängerkupplung. Stecken
Sie den Sicherungsstift hinein und schließen Sie
die Arretierung. Wickeln Sie den Sicherungsriemen
zweimal um den Fahrradrahmen und befestigen Sie
ihn an der Öse an der Zugstange (Abbildung 19).
CHILD TRAILER MANUAL 15
… 18 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Burley D-Lite 2015 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Burley D-Lite 2015 in the language / languages: English, German, French, Spanish as an attachment in your email.

The manual is 5,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info