678325
218
Zoom out
Zoom in
Previous page
1/245
Next page
217
Chapter 8 Drive Replacement
Replacing SSDs on the TS5210DF Series When Data
Protection Mode Is Enabled
When data protection mode is enabled, a warning message to notify you that too many bad blocks have been
detected on the drive after logging in to Settings. In such a case, back up data on the drive and replace it. When a
drive with bad blocks is replaced in a RAID 0 or JBOD array, all data on the array will be lost. The procedure
may vary depending on what RAID mode you have configured. Do not perform the following procedure unless the
bad blocks warning message appears and data protection mode is enabled. If another drive error message such as
the E30 message appears, follow the replacement procedure described at the “Replacing Drives on Another Unit
Series Other Than the TS51210RH Series” section above.
Using RAID 1
When too many bad blocks occur on both drives in the RAID array, the TeraStation will be in data protection mode. If
both drives need replacement, replace them one by one.
1 From Settings, click Storage.
2 Click to the right of “Drives”.
3 Select a drive and click S.M.A.R.T. to check whether the current value of “Reallocated_Sector_Ct” is 99 or less.
4 Click Close.
5 Select a drive whose current value of “Reallocated_Sector_Ct is 99 or less and click Dismount Drive.
6 The “Confirm Operation” screen will open. Enter the confirmation number, then click OK.
7 When the dismount process is completed, the TeraStation will beep and the I12 and E30 messages appear.
Press the display button to stop the TeraStation beeping.
8 Open the front panel with the included key.
9 The dismounted drives status LED will be glowing red. Push its unlock button and swing the lock mechanism
out.
10 Pull out the drive cartridge and remove it from the TeraStation.
11 Insert the new drive into the empty slot. Slide the drive in with the locking mechanism open.
12 Swing the lock back down until it clicks into place.
13 Close the front cover.
14 When the replaced drive is recognized, the status LED will flash red and the I32 message will appear on the
LCD panel.
15 Press the function button on the front of the TeraStation. The TeraStation will beep and start rebuilding the
RAID array automatically. After a few minutes, the I18 message will be displayed until the array is rebuilt.
16 After the rebuilding process is completed, repeat the steps 5–14 for another drive with bad blocks.
218


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Buffalo TeraStation 5410 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Buffalo TeraStation 5410 in the language / languages: English as an attachment in your email.

The manual is 11,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Buffalo TeraStation 5410

Buffalo TeraStation 5410 User Manual - German - 259 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info