678325
217
Zoom out
Zoom in
Previous page
1/245
Next page
216
Chapter 8 Drive Replacement
13 The “Confirm Operation screen will open. Enter the confirmation number, then click OK.
14 From Storage > Drives, click Format Drive to format the new drive.
15 The “Confirm Operation screen will open. Enter the confirmation number, then click OK.
16 From Storage > RAID, choose “RAID 0” from the RAID mode drop-down list and click Create RAID Array.
17 The “Confirm Operation screen will open. Enter the confirmation number, then click OK.
18 When creating a new RAID 0 array is completed, create a shared folder before use.
Using a Hot Spare
If your TeraStations drives are in a redundant RAID mode and you have a hot spare enabled, a malfunctioning drive
in the array is replaced by the spare drive and the RAID array is rebuilt automatically. The status LED will continue to
glow red for the failed drive even after the RAID array is rebuilt with the hot spare. After you replace the failed drive
with a new drive, follow the procedure below to configure a spare drive as a new drive.
1 Open the front cover with the included key.
2 The failed drive’s status LED will be glowing red. Push its unlock button and swing the lock mechanism out.
3 Pull out the drive cartridge and remove it from the TeraStation.
4 Insert the new drive into the empty slot. Slide the drive in with the locking mechanism open.
5 Swing the lock back down until it clicks into place.
6 Close the front cover.
7 When the replaced drive is recognized, the status LED will flash red and the I31 message will appear on the
LCD panel.
8 Press the function button on the front of the TeraStation. The TeraStation will beep. The replaced drive is
automatically registered as a hot spare.
To use the replaced drive as a normal drive rather than a hot spare, navigate to Storage > RAID and click the
RAID array, select the new drive, and click Set as a normal drive.
Note: If a drive fails in the RAID array before it is rebooted, the hot spare will not automatically replace the failed
drive. In this case, follow the procedure below to repair the array.
(1) From Settings, navigate to Storage > Drives.
(2) Click the drive that was configured as a hot spare, then click Dismount Drive.
(3) Click Rediscover Drive.
(4) Navigate to Storage > RAID.
(5) Choose the RAID array to repair.
(6) Click the drive that was previously configured as a hot spare, then click Recover RAID Array.
This will rebuild the RAID array.
217


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Buffalo TeraStation 5410 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Buffalo TeraStation 5410 in the language / languages: English as an attachment in your email.

The manual is 11,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Buffalo TeraStation 5410

Buffalo TeraStation 5410 User Manual - German - 259 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info