636472
16
Zoom out
Zoom in
Previous page
1/56
Next page
7
Boiler block assembly
Logano G315 – 6 720 817 939 (2016/04)16
Fig. 18 Boiler assembly tool on rear section
Place both ratchet wrenches onto clamping nuts of the compression
unit and press boiler sections together by tightening evenly.
Release and remove the boiler assembly tool.
Check nipples are seated correctly.
The boiler sections must be aligned to make the installation easier.
Assemble all other boiler sections as described. The front section is
always fitted last.
After the front section is attached, loosen – the assembly tool but do
not remove it.
Insert the tie rod before removing the assembly tool!
Insert the three tie rods (with spring packs fitted) into the cast lugs at
the designated positions (Fig. 19 [1, 2, and 3]). When inserting the
tie rods, make sure the spring packs are mounted on the rear of the
boiler.
Put a nut onto each of the threaded tie rods and tighten by hand.
Now tighten the nuts on the tie rods 1 to 1½ turns.
Level the boiler block vertically and horizontally on the base/
foundation ( Chapter 6.3, page 12).
Remove boiler assembly tool.
Fig. 19 Fitting the tie rods
The next step describes the installation of the supply pipe
( Chapter 7.4, page 17).
7.3 Setting up the boiler block (assembled block)
Cut the retaining band (Fig. 20, [1]).
Remove the pallet prior to positioning the boiler block (Fig. 20, [2]).
Fig. 20 Boiler block on pallet
Level the boiler block vertically and horizontally on the base/
foundation ( Chapter 6.3, page 12).
The following pages describe the installation of the supply pipe and
sensor well. You must do both irrespective of whether the boiler is
supplied pre-assembled or in separate sections.
NOTICE:
Never compress more than one nipple connection
(two sections) per pressing operation since
otherwise the boiler block could compress unevenly.
This causes leaks in the nipple connections.
NOTICE:
If the boiler packing grooves hit each other,
immediately stop any compression. Additional
compression could damage the boiler sections.
NOTICE: Damage to system through excessively low
contact pressure.
Do not compress the spring pack. Only use the spring
pack in its original state.
DANGER: Risk of fatal injury from falling objects.
Provide a suitable means of supporting the load.
Observe all locally applicable occupational health &
safety regulations regarding lifting equipment.
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Buderus Logano G315 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Buderus Logano G315 in the language / languages: English as an attachment in your email.

The manual is 3,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Buderus Logano G315

Buderus Logano G315 User Manual - English - 8 pages

Buderus Logano G315 Installation Guide - French - 56 pages

Buderus Logano G315 User Manual - French - 8 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info