560474
37
Zoom out
Zoom in
Previous page
1/100
Next page
BC10 basic controller 10
37
We reserve the right to make any changes due to technical modifications!
Installation and Servicing Instructions Logamax plus GB142-24/30/45/60 • Version 12/2004
Buderus Hydronic Systems • http://www.buderus.net
Resetting the appliance or resetting faults
If the appliance is down due to a fault, you can reset the
appliance by pressing the "Reset"
button. This is only
possible for so-called lock-out faults. There is another
type of fault, so-called blocking faults, that reset them-
selves when the cause has been remedied.
z Press the "Reset"
button to reset the appliance.
The display shows "U(" while resetting.
It is only possible to reset the appliance when a lock-out
code (blinking fault code) is visible in the display.
10.1.3 Displaying the heating system status and/or
faults
The display of the BC10 basic controller shows the
status of the heating system.
In the event of a fault the display immediately shows the
fault or the warning in the form of an error code (see
subsection 16.2). The status display will flash if the fault
is a lock-out fault.
z Press the "Service"
button to switch between
status displays or to read out the service and error
codes.
z Resolve the fault see subsection 16.3.
The following status displays can be seen depending on
the operating conditions:
U(
NOTICE
If the burner returns to fault mode after reset-
ting the appliance, you must resolve the fault
using the servicing section in this document.
Contact your supplier if necessary.
Displays
(examples)
Values Meaning Operating condition/Remedy
1
number
0 ... 199
Current heater water temperature (in °F)
> P15 Current system pressure (in psi) Normal operating conditions
1
(changing)
P3 ... P12 Warning:
System pressure is too low (between 3 and 12 psi
= 0.2 and 0.8 bar)
Warning
Heating system remains operational
between 12 psi and 3 psi (0.8 and 0.2 bar).
Fill the heating system and restore the
minimum filling pressure (t 14.5 psi =
t 1.0 bar).
The system pressure is shown for
10 minutes after which the standard
display returns.
number
0 ... 199
Current heater water temperature (in °F)
P3 ... P12 Current system pressure (in psi)
Table 9 Possible status displays
1
Standard display for this operating condition. This display appears after 5 minutes if no button is pressed.

3
+
3
+
+

3
37


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Buderus Logamax plus GB142-45 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Buderus Logamax plus GB142-45 in the language / languages: English as an attachment in your email.

The manual is 4,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Buderus Logamax plus GB142-45

Buderus Logamax plus GB142-45 User Manual - German - 16 pages

Buderus Logamax plus GB142-45 User Manual - Dutch - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info