525945

Brother XR-46C Manual

48
Zoom out
Zoom in
Previous page
1/99
Next page
37
KNOWING YOUR SEWING MACHINE
CONNAITRE SA MACHINE A COUDRE
CONOZCA SU M
ÁQUINA DE COSER
A
B
1
2
INSERTING THE TWIN NEEDLE
Insert in the same way a single needle is inserted (refer to page 9).
The flat side of the needle should face toward the back and the
rounded side should face toward you.
PLACING THE EXTRA SPOOL PIN
Place the vertical spool pin in the hole found on top of the machine
near the horizontal spool pin. Place the second spool of thread onto
the vertical spool pin as shown in fig. A.
TWIN NEEDLE THREADING
Each needle should be threaded separately.
1. Threading the Right Needle
Follow the same instructions for single needle threading using
the thread from the spool on the extra spool pin. See page 31 for
more details.
2. Threading the Left Needle
Thread the left needle in the same manner that the right needle
was threaded, but do not pass the thread through the thread
guide above the needle before passing it through the eye of the
left needle as shown below in fig. B.
1 Right needle thread passes through this guide.
2 Left needle thread passes in front of this guide.
CAUTION
The needle threader can not be used. Thread the twin needle
by hand, from front to back. Using the needle threader may
result in damage to the machine.
MISE EN PLACE DE L’AIGUILLE JUMELEE
Introduire l’aiguille comme pour une aiguille normale (veuillez vous
référer à la page 10). Le côté plat de l’aiguille doit être tourné vers l’arrière
et l’arrondi doit se situer face à l’utilisateur.
POUR PLACER UN PORTE-BOBINE SUPPLEMENTAIRE
Placer le porte-bobine vertical dans l’orifice qui se trouve au-dessus de la
machine, près du porte-bobine horizontal. Placer la seconde bobine de fil
sur l’axe vertical comme le montre la fig. A.
ENFILAGE DE L’AIGUILLE JUMELEE
Chaque aiguille doit être enfilée séparément.
1. Enfilage de l’aiguille de droite
Respecter les instructions fournies pour l’enfilage d’une seule aiguille
mais en utilisant le fil de la bobine placée sur le porte-bobine supplé-
mentaire. Voir page 32 pour de plus amples détails.
2. Enfilage de l’aiguille de gauche
Enfiler l’aiguille de gauche de la même manière que l’aiguille de droite
mais sans passer le fil par le guide-fils situé au-dessus de l’aiguille.
Passer directement le fil par le chas de l’aiguille gauche, comme le
montre la fig. B.
1 Le fil de l’aiguille droite passe par le guide-fils.
2 Le fil de l’aiguille gauche passe devant le guide-fils.
ATTENTION
Vous ne pouvez utiliser l’enfileur d’aiguille. Enfilez l’aiguille jumelée
manuellement, de l’avant à l ’arrière. Si l’enfileur d’aiguille est utilisé,
la machine pourrait être endommagée.
PARA INTRODUCIR LA AGUJA DOBLE
Introdúzcala de la misma manera que una aguja simple (véase página
10). La parte plana de la aguja debe estar cara hacia atrás mientras
que la parte redonda está cara a usted.
COLOCADO EL EJE DE CARRETE SUPLEMENTARIO
Coloque el eje de carrete vertical en el orificio previsto arriba de la
máquina, cerca del eje horizontal. Instale el segundo carrete de hilo
en el eje vertical, tal como ilustrado en la fig. A.
ENHEBRADO DE LA AGUJA DOBLE
Cada una de las agujas debe ser enhebrada por separado.
1. Enhebrado de la aguja derecha
Observe las mismas instrucciones que para el enhebrado de una
sola aguja, pero utilizando el hilo del carrete colocado en el porta
carretes extra. (véase página 32 para mayores detalles al respec-
to).
2. Enhebrado de la aguja izquierda
Enhebre la aguja izquierda de la misma manera que la aguja
derecha. Sin embargo, no hay que pasar el hilo por la guía que se
sitúa arriba de la aguja. Conviene pasarlo directamente por el ojo
de la aguja izquierda, tal como ilustrado arriba en la fig. B.
1 El hilo de la aguja derecha pasa por la guía.
2 El hilo de la aguja izquierda pasa delante de la guía.
PRECAUCIÓN
No utilice el enhebrador. Enhebre la aguja doble con la mano, de
delante atrás. Si usa el enhebrador, podría estropear la máquina.
… 48 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother XR-46C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother XR-46C in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 1,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info