631397
22
Zoom out
Zoom in
Previous page
1/101
Next page
11
KNOWING YOUR SEWING MACHINE
KENNENLERNEN IHRER MASCHINE
КРАТКОЕ ТЕХНИЧЕСКОЕ ОПИСАНИЕ МАШИНЫ
Changing the Presser Foot
CAUTION
Always turn off the power before changing the presser
foot. If the power is on and controller is stepped on, the
machine will start and may cause injury.
Always use the correct presser foot for the selected
stitch pattern. If the wrong presser foot is used, the
needle may strike the presser foot and bend or break,
and may cause injury.
Only use presser feet for this machine. Using other
presser feet may lead to accident or injury.
It may be necessary to change the presser foot according to your
sewing needs.
SNAP-ON TYPE
1. Raise the needle to its highest position by turning the balance
wheel toward you (counter clockwise) and raise the presser foot
lever.
2. Release the foot by raising the lever located at the back of the
holder.
3. Place a different presser foot on the needle plate so that the bar
on the presser foot is in line with the slot on the shank.
4. Lower the presser foot lever and fix the presser foot onto the
shank. If the presser foot is in the correct location, the bar should
snap in.
Nähfuß wechseln
VORSICHT
Schalten Sie die Maschine immer am Netzschalter aus, bevor
Sie den Nähfuß auswechseln. Wird bei eingeschaltetem Strom
versehentlich der Fußanlasser betätigt beginnt die Maschine
zu nähen, und es kann zu Verletzungen kommen.
Benutzen Sie immer den richtigen Nähfuß für das jeweilige
Stichmuster. Wird der falsche Nähfuß benutzt, kann die Nadel
auf den Nähfuß treffen und sich dadurch verbiegen oder
abbrechen, so daß es zu Verletzungen kommen kann.
Benutzen Sie nur Nähfüße speziell für diese Maschine. Die
Verwendung anderer Nähfüße kann Unfälle und Verletzun-
gen zur Folge haben.
Es kann nötig sein, den Nähfuß zu wechseln, je nachdem, was Sie nähen
möchten.
SCHNAPPVERSCHLUSS
1. Bringen Sie die Nadel auf die höchste Position, indem Sie das Handrad
auf sich zu bewegen (entgegen dem Uhrzeigersinn). Heben Sie dann
den Nähfußhebel an.
2. Lösen Sie den Fuß, indem Sie den Hebel an der Rückseite des
Nähfußhalters anheben.
3. Setzen Sie einen anderen Nähfuß auf die Stichplatte, so daß der
Querbalken auf dem Nähfuß unter dem Schlitz des Halters sitzt.
4. Senken Sie den Nähfußhebel und fixieren Sie den Nähfuß auf den
Nähfußhalter. Wenn der Nähfuß richtig ausgerichtet ist, sollte der
Querbalken einrasten.
Замена нажимной лапки
ПРЕДОСТЕРЕЖЕНИЕ
Перед заменой нажимной лапки всегда отключайте
питание. Если питание не выключено, то при
случайном нажатии на педаль контроллера машина
включится, и Вы можете получить травму.
Всегда используйте нужный тип нажимной лапки
для выполнения выбранного Вами вида строчки.
При использовании неправильной нажимной лапки
игла может ударить нажимную лапку, изогнуться
или сломаться, и Вы можете получить травму.
Используйте только нажимные лапки,
предназначенные для данной модели швейной
машины. Использование других нажимных лапок
может привести к несчастному случаю или
получению травмы.
В зависимости от характера выполняемой строчки может
возникнуть необходимость в замене нажимной лапки.
ЛАПКИ С ПРУЖИННОЙ ЗАЩЕЛКОЙ
1. Поднимите иглу в крайнее верхнее положение вращением
маховика на себя (против часовой стрелки при виде с
торца) и поднимите рычаг нажимной лапки.
2. Освободите лапку подъемом рычага, находящегося в
задней части механизма держателя лапки.
3. Разместите новую лапку на игольной пластине таким
образом, чтобы ось лапки располагалась на одной линии с
прорезью на механизме держателя лапки.
4. Опустите рычаг нажимной лапки и зафиксируйте лапку в
держателе. При правильном позиционировании лапки
пружинный фиксатор автоматически защелкнется.
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother XL-6040 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother XL-6040 in the language / languages: English as an attachment in your email.

The manual is 1,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother XL-6040

Brother XL-6040 User Manual - German, Dutch, French - 101 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info