631397
21
Zoom out
Zoom in
Previous page
1/101
Next page
10
KNOWING YOUR SEWING MACHINE
KENNENLERNEN IHRER MASCHINE
КРАТКОЕ ТЕХНИЧЕСКОЕ ОПИСАНИЕ МАШИНЫ
Nadel prüfen
Die Nähnadel muß für problemloses Nähen immer gerade und spitz sein.
Richtiges Überprüfen der Nadel:
Um die Nadel zu überprüfen, legen Sie sie mit der abgeflachten Seite auf
eine plane Oberfläche. Überprüfen Sie die Nadel von oben und an allen
Seiten. Verbogene Nadeln müssen entsorgt werden und dürfen keinesfalls
verwendet werden.
1 Paralleler Abstand
2 Plane Oberfäche (Stichplatte, Glas, etc.)
* Legen Sie die Nadel auf eine plane Oberfläche.
Nadel austauschen
VORSICHT
Schalten Sie die Maschine am Netzschalter AUS, bevor Sie die
Nadel auswechseln. Wird bei eingeschaltetem Strom verse-
hentlich der Fußanlasser betätigt beginnt die Maschine zu
nähen, und es kann zu Verletzungen kommen.
Benutzen Si
e nur Nadeln des Systems 130/705 H.
Andere Nadeln können abbrechen u
nd zu Verletzungen führen.
Verwenden Sie zum Nähen keine verbogenen Nadeln. Verbo-
gene Nadeln können leicht abbrechen und Verletzungen zur
Folge haben.
1. Ziehen Sie den Netzstecker aus der Steckdose.
2. Drehen Sie den Nadelhalter auf die höchste Position.
3. Senken Sie den Nähfuß ab.
4. Nehmen Sie die Nadel heraus, nachdem Sie die Nadelschraube gelöst
haben.
1 Nähfusshebel
VORSICHT
Lösen oder befestigen Sie die Schraube des Nadelhalters nicht mit zu
hoher Kraft. Dies könnte zudes Nadelhalters der Nadel oder der
Maschine führen.
5. Stecken Sie die Nadel mit der abgeflachten Seite nach hinten gerichtet
bis zum Nadelanschlag hinein. Ziehen Sie die Schraube mit Hilfe eines
Schraubendrehers fest an.
2 Nadelanschlag
3 Nadelkanal
4 Abgeflachte Seite der Nadel
VORSICHT
Achten Sie darauf, daß Sie die Nadel bis zum Anschlag eingeführt
und die Nadelklemmschraube fest mit einem Schraubendreher
angezogen haben. Wurde die Nadel nicht richtig eingeführt oder
die Schraube nicht fest genug angezogen, kann die Nadel abbre-
chen oder die Maschine beschädigt werden.
Проверка иглы
Во избежание проблем в процессе шитья швейная игла всегда
должна быть строго прямолинейной и остро заточенной.
Для того, чтобы правильно проверить состояние иглы:
Для проверки иглы положите ее на ровную поверхность
плоской стороной вниз. Проверьте иглу, осмотрев ее сверху и
с боков. Выбросьте изогнутые иглы.
1 Параллельное расположение
2
Ровная поверхность (крышка шпульки, стекло, и т.д.)
* Положите иглу на ровную поверхность.
Замена иглы
ПРЕДОСТЕРЕЖЕНИЕ
Перед заменой иглы обязательно установите
выключатель питания в положение «ВЫКЛЮЧЕНО».
Если выключатель питания оставить во включенном
состоянии, то при случайном нажатии на педаль
контроллера машина включится, и Вы можете
получить травму.
Для бытового использования рекомендуем
применять только швейные иглы для швейных
машин. Использование иных типов игл может
привести к их поломке, изгибам или к получению
травмы.
Никогда не шейте изогнутой иглой. Изогнутые иглы
легко ломаются, что приводит к травмам.
1. Отсоедините штепсель шнура питания от розетки.
2. Поднимите игловодитель в крайнее верхнее положение.
3. Опустите нажимную лапку.
4. Снимите иглу, освободив крепежный винт на игловодителе.
1 Рычаг нажимной лапки
ПРЕДОСТЕРЕЖЕНИЕ
Не применяйте излишних усилий при отвинчивании или
затягивании крепежного винта на игловодителе во
избежание его повреждений.
5. Сориентировав новую иглу плоской стороной назад,
вставьте ее до упора вверх (см. окошко на рисунке).
Надежно затяните крепежный винт отверткой.
2 Игольный упор
3 Отверстие для установки иглы
4 Плоская сторона иглы
ПРЕДОСТЕРЕЖЕНИЕ
Обязательно вставьте иглу до упора и затяните
крепежный винт отверткой. Если игла вставлена не
полностью, или если крепежный винт ослаблен, игла
может сломаться или повредить швейную машину.
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother XL-6040 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother XL-6040 in the language / languages: English as an attachment in your email.

The manual is 1,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother XL-6040

Brother XL-6040 User Manual - German, Dutch, French - 101 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info