Manual Brother XL-5030 (page 68 of 82) (English, Italian, Spanish)

631388

Zoom out

Zoom in

1/82

CONTENTS

KNOWING YOUR

SEWING MACHINE

STRAIGHT AND

ZIGZAG STITCHING

BUILT-IN STITCHES

BUTTONHOLE AND

BUTTON SEWING

USING ATTACHMENTS

AND APPLICATIONS

MAINTENANCE

INDEX

Monogramming and Embroidering

XL5030 XL5020 XL5010

Pattern Stitch Length Stitch Width Foot

4 4 2 Zigzag Stitch Fixed 1.7

5 5 3 Zigzag Stitch -2 Fixed 3.5 None

6 6 4 Zigzag Stitch Fixed 5

Preparing for Monogramming and Embroidering

1. Place the darning plate on the needle plate.

(When the machine is equipped with a drop feed lever, lower the

feed dogs by setting the drop feed lever to the up position.)

2. Set the pattern selection dial to the appropriate Zigzag Stitch.

3. Draw the lettering (for monogramming) or design (for embroider-

ing) on the surface of the fabric.

4. Stretch the fabric between embroidery hoops as firmly as possible

with the reverse side of the fabric under the inside hoop.

5. Place the work under the needle and lower the presser bar with the

presser foot holder assembly removed.

6. Pull the lower thread up through the work at the starting position

by turning the balance wheel and make a few holding stitches.

7. Hold the hoop with the thumbs and forefingers of both hands while

pressing the fabric with the middle and third fingers and supporting

the outside of the hoop with your small fingers.

NOTE:

After sewing without feeding, prepare for the next seam by returning

the drop feed lever to the down position so that the feed dogs are

raised.

CAUTION:

Keep fingers away from moving parts, especially needles.

Monogramas y bordados

XL5030 XL5020 XL5010

Número de puntada

Largo de puntada Ancho de puntada

Prensatelas

442

Puntada zigzag

Fija 1,7

Quitarlo, sin

553

Puntada zigzag

-2 Fija 3,5

664

Puntada zigzag

Fija 5

prensatelas

Preparación para monogramas y bordados

1. Coloque la placa de zurcido en la placa de la aguja.

(Cuando la máquina está equipada con una palanca de alimen-

tación de bajada, baje los ganchos de alimentación colocando la

palanca de alimentación de bajada en la posición hacia arriba).

2. Ponga el selector de puntadas en la puntada zigzag apropiada.

3. Dibuje las letras (para monogramas) o el diseño (para bordados)

en el derecho del tejido.

4. Estire el tejido en bastidor tanto como pueda y si es posible con

el revés abajo del circulo interior.

5. Coloque la tela debajo de la aguja y baje la barra del prensatelas

con su soporte.

6. Girando la ruedecilla, pase el hilo inferior por el trabajo y cosa

unas cuantas puntadas para asegurarlo.

7. Sujete el bastidor con el pulgar e índice de cada mano, presione

el tejido con los dedos medios y anulares y sostenga los exterio-

res del bastidor con los meñiques.

NOTA:

Después de haber cosido sin la alimentación, prepárese para la si-

guiente costura bajando la palanca para que se levanten los

alimentadores.

ATENCIÓN:

Mantenga los dedos alejados de las piezas móviles, especial-

mente de las agujas.

Monogrammi e ricami

XL5030 XL5020 XL5010

Punto Lunghezza Ampiezza Piedino

4 4 2 Punto zigzag Fissa 1,7

5 5 3 Punto zigzag -2 Fissa 3,5 Nessuno

6 6 4 Punto zigzag Fissa 5

Preparazione per la cucitura di monogrammi e ricami

1. Posizionare la placca da rammendo sulla placca dell’ago (se la macchi-

na è equipaggiata con la leva abbassa-trasportatore, abbassare il tra-

sportatore spostando la leva verso l’alto).

2. Ruotare il selettore dei punti sul punto zigzag appropriato.

3. Disegnare le lettere che comporranno il monogramma o il motivo orna-

mentale da rammendare sul diritto del tessuto.

4. Mettere il tessuto in un cerchietto da ricamo tenendolo ben teso, con il

rovescio del tessuto sotto al cerchietto interno.

5. Disporre il lavoro sotto l’ago e abbassare la barra di pressione a cui sarà

stato tolto in precedenza il supporto del piedino premistoffa.

6. Girando il volantino, tirare su il filo inferiore facendolo passare attra-

verso il lavoro nella posizione di inizio e cucire alcuni punti di fissag-

gio.

7. Usando entrambe le mani, tenere il cerchietto fra il pollice e l’indice e

nello stesso tempo premere il tessuto con il medio e l’anulare reggendo

con i mignoli il bordo esterno del cerchietto.

NOTA:

Dopo aver cucito senza trasporto, preparare la cucitura successiva riportan-

do la leva abbassa-trasportatore in posizione abbassata per alzare il traspor-

tatore.

ATTENZIONE:

Tenere le dita lontano dalle parti in movimento, in particolare dall’ago.

I'm a complete notice, and need your help.
I was using my sewing machine and the unit that holds the needle came off the main rod that moves up and down.. There seems to be a tiny alan screw, is that what holds it on the rod? Would need a tiny alan key..

Thank you for any help..
Kind regards
Helen Submitted on 10-10-2020 at 20:19
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Brother XL-5030 in the language / languages: English, Italian, Spanish as an attachment in your email.

The manual is 1,53 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother XL-5030

Brother XL-5030 User Manual - German, Dutch, French - 85 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Brother XL-5030 Manual

Product: