Manual Brother Super Galaxie3000D (page 303 of 319) (English)

555756

303

Zoom out

Zoom in

1/319

9-8 Troubleshooting

1 —

2 —

3 —

4 —

5 —

6 —

7 —

8 —

9 —

CONTENTS

Index

1 Needle is installed incorrectly.

2 Needle clamp screw is not tightened.

3 Needle is turned or bent.

4 Using improper needle or thread for the

selected fabric.

5 Wrong presser foot was used.

6 Upper thread tension is too strong.

7 Fabric is pulled during sewing.

8 Spool cap is set incorrectly.

9 There are scratches around the holes

in the needle plate.

0 There are scratches around the hole(s)

in the presser foot.

A There are scratches on the race.

B Needle is defective.

1 Feed dogs are set in the down position.

2 Stitches are too close together.

3 Wrong presser foot was used.

4 Needle is turned, bent or the point is dull.

5 Thread is entangled.

Problem Cause

PageSolution

Reinstall the needle correctly.

Tighten the needle clamp screw.

Replace the needle.

Check the “Fabric/Thread/Needle

Combination” chart.

Use the recommended presser

foot.

Adjust the thread tension setting.

Do not pull the fabric during sew-

ing.

Check the method for attaching the

spool cap, then reattach the spool

cap.

Replace the needle plate, or con-

sult your authorized dealer.

Replace the presser foot, or con-

sult your authorized dealer.

Replace the race, or consult your

authorized dealer .

Replace the needle.

Use the feed dog position lever to

raise the feed dogs.

Lengthen the stitch length setting.

Use the correct presser foot.

Replace the needle.

Cut the entangled thread and re-

move it from the race.

Fabric does

not feed

through the

machine

Needle

breaks

1-43

1-44

1-43

1-45

3-1

2-13, 5-40

—

1-33

8-2

1-39

8-2

1-43

1-6

2-9

3-1

1-43

7-2

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Brother Super Galaxie3000D in the language / languages: English as an attachment in your email.

The manual is 7,79 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Brother Super Galaxie3000D Manual

Product: