718890
186
Zoom out
Zoom in
Previous page
1/244
Next page
184
Specifying jumpstitch trimming /
“DST” jump codes for trimming
You can specify whether or not jumpstitches are
cut. In addition, when using Tajima embroidery
data (.dst), you can specify whether or not the
thread is cut according to the specified number of
jump codes.
ON: The machine cuts the upper and bobbin
thread before the jumpstitch. When Tajima
embroidery data (.dst) is used, the machine
converts the “jump” code to a trim code, based on
the number specified on the next line.
OFF: The machine does not cut either a jumpstitch
or the “jump” code in Tajima embroidery data
(.dst).
When the machine is purchased, “ON” is selected
and the number of jumps is set to “3”.
The “DST” thread trim settings can be specified
from page 2 of the settings screen.
a
Touch or to select the desired
setting.
When using Tajima embroidery data
(.dst)
b
If “ON” is selected, touch and to
select the number of feed codes.
The desired setting is displayed.
A value between 1 and 8 can be specified. For
example, if 3 is specified, sequential 3 jump codes
will be converted to the trim code. But sequential 2
jump codes will not be converted to the trim code, it
will be sewed as the feed (jump) stitch.
Deleting short stitches
If embroidery data other than our original patterns
are used, the stitch length may be too short,
possibly resulting in the thread or the needle
breaking. In order to prevent this problem from
occurring, the machine can be set to delete
stitches with a short stitch length. Stitches with a
length less than that specified in this function, can
be deleted.
When the embroidery machine is purchased,
“0.3” was selected (delete stitches with a length of
0.3 mm or less).
Note
If the setting is changed from the previous
setting, the new setting is only applied to
the next embroidery.
Note
This setting is not applied to the trimming of
threads between characters in alphabet
patterns. (Refer to “Trimming the threads
between characters” on page 155.)
Memo
The number of jump codes cannot be
specified for data other than Tajima
embroidery data (.dst).
Note
You need to set the jump number same as
the number that was used when the
particular Tajima data was created.
If the jump number is not matched, either
unexpected trim or no trimming at trim
expected point will happen.
186


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother PR-670E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother PR-670E in the language / languages: English as an attachment in your email.

The manual is 11,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother PR-670E

Brother PR-670E User Manual - German - 244 pages

Brother PR-670E User Manual - Dutch - 244 pages

Brother PR-670E User Manual - French - 244 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info