555741

Brother LS1217 Manual

55
Zoom out
Zoom in
Previous page
1/81
Next page
45
CONTENTS INDEXMAINTENANCE
KNOWING YOUR
SEWING MACHINE
STRAIGHT AND
ZIGZAG STITCHING
BUILT-IN STITCHES
BUTTONHOLE AND
BUTTON SEWING
USING ATTACHMENTS
AND APPLICATIONS
Darning
STITCH LENGTH F-2
STITCH WIDTH 0
NEEDLE POSITION M
PRESSER FOOT None
NEEDLE Single
OTHER Darning plate
1. Place the darning plate on the needle plate and press down into
place as shown in fig. A on the next page.
2. Place the portion to be darned under the presser foot together with
a fabric underlay for reinforcement.
3. Remove the presser foot, then lower the presser foot lifter.
4. Begin sewing alternating between gently drawing the work away
from you and pulling it toward you. With the darning plate on the
machine, the feed dogs will not move the fabric. You control the
fabric movement with your hands.
5. Repeat this motion until the portion to be darned is filled with par-
allel lines of stitching. See fig. B.
A
B
Reprisage
LONGUEUR DE POINT F-2
LARGEUR DE POINT 0
POSITION DE L’AIGUILLE M
PIED-DE-BICHE Aucun
AIGUILLE Simple
AUTRE Plaque à repriser
1. Placer la plaque à repriser sur la plaque à aiguille et appuyer pour
la mettre en place correctement comme l’indique la fig. A de la
page suivante.
2. Placer la pièce à repriser et une pièce de renfort sous le pied-de-
biche.
3. Retirer le pied-de-biche et baisser le levier de pied-de-biche.
4. Commencer à coudre en alternativement tirant et poussant le tissu
doucement. La plaque à repriser sur la machine, les griffes d’en-
traînement n’entraîneront pas le tissu. Le tissu est déplacé manuel-
lement.
5. Continuer jusqu’à que la pièce à repriser soit couverte de lignes
parallèles de points. Voir fig. B.
Zurcido
LARGO DE LA PUNTADA F-2
ANCHO DE LA PUNTADA 0
POSICIÓN DE LA AGUJA M
PRENSATELAS Retirado
AGUJA Simple
OTROS Placa de zurcir
1. Instale la placa de zurcir sobre la placa de agujas y apriete para
engancharla como se indica en la fig. A de la siguiente página.
2. Ponga el tejido a zurcir debajo del prensatelas con una pieza de
tela de refuerzo debajo.
3. Quite el prensatelas, y luego baje el elevador del prensatelas.
4. Empiece a coser empujando y tirando alternativamente del tejido
con cuidado. Cuando la placa de zurcir está instalada en la má-
quina, los alimentadores no mueven el tejido. Su movimiento se
controla únicamente con las manos.
5. Repita este movimiento hasta que la parte que va a zurcirse se
llene con líneas paralelas de puntadas. Véase fig. B.
Remendos
COMPRIMENTO DO PONTO F-2
LARGURA DO PONTO 0
POSIÇÃO DA AGULHA M
PÉ CALCADOR Nenhum
AGULHA Simples
OUTROS Chapa de Cerzir
1. Coloque a chapa de cerzir na chapa de agulha e pressione-a no lugar
como mostra a fig. A na próxima página.
2. Coloque a porção a ser remendada sob o pé calcador, junto com um
tecido de forro para reforço.
3. Remova o pé calcador e então abaixe o ascensor de pé calcador.
4. Comece a costurar, alternando entre afastar e puxar para si o trabalho
gentilmente. Com a chapa de cerzir na máquina, os dentes impelentes
não moverão o tecido. Você controlará o movimento do tecido com as
suas mãos.
5. Repita este movimento até que a porção a ser remendada seja preenchi-
da com linhas paralelas de costura. Veja a fig. B.
… 55 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother LS1217 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother LS1217 in the language / languages: English, French, Portuguese, Spanish as an attachment in your email.

The manual is 1,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info