Manual Brother LS1217 (page 26 of 81) (English, French, Portuguese, Spanish)

555741

Zoom out

Zoom in

1/81

CONTENTS INDEXMAINTENANCE

KNOWING YOUR

SEWING MACHINE

STRAIGHT AND

ZIGZAG STITCHING

BUILT-IN STITCHES

BUTTONHOLE AND

BUTTON SEWING

USING ATTACHMENTS

AND APPLICATIONS

Upper (Needle) Threading

1 Spool pin

2 Thread guide

3 Thread Take Up Lever

4 Upper (needle) Tension

5 Thread Check Spring

6 Lower Thread Guide

1. Raise the presser foot using the presser foot lever and turn the bal-

ance wheel toward you (counterclockwise) to raise the thread take

up lever to the highest position.

2. Pull up the spool pin and place a spool of thread on the pin.

3. Pass the thread through the first guide as shown and then forward

into the right side slot on the front of the machine.

4. Guide the thread down from the right slot and around the upper

tension to the left seeing that the thread picks up the check spring

at the left of the tension area. (fig. A and B)

5. Guide the thread up the left side slot making sure that the thread is

to the right side of the thread take up lever until the thread is be-

hind the take up lever. Guide the thread to left bringing it up against

the take up lever and then continue down towards the needle

through the left side slot. This motion should automatically thread

the take up lever. (fig. C)

6. Bring the thread down to the needle area passing it behind the

thread guide just above the needle. (fig. D)

7. Thread the needle from front to back leaving a thread tail of about

5 cm (2").

NOTE:

If thread is incorrectly fed, the thread may break, cause stitches to be

skipped or cause the fabric to pucker.

Mise en place du fil supérieur (aiguille)

Porte-bobine

Guide-fil

Levier releveur de fil

Sélecteur de tension supérieure (aiguille)

Ressort d’arrêt de fil

Guide-fil inférieur

1. Lever le pied-de-biche à l’aide de son levier et tourner le volant

vers soi (dans le sens contraire des aiguilles d’une montre) pour

remonter complètement le levier releveur de fil.

2. Tirer le porte-bobine vers le haut et placer une bobine de fil sur le

porte-bobine.

3. Faire passer le fil dans le premier guide comme indiqué puis le

faire passer dans la fente droite avant située à l’avant de la ma-

chine.

4. Guider le fil à partir de la fente droite, vers le bas et sur le sélecteur

de tension supérieure, vers la gauche, en veillant à ce que le fil

prenne bien le ressort d’arrêt à gauche du sélecteur de tension. (fig.

A et B)

5. Guider le fil dans la fente gauche en s’assurant que le fil est sur la

droite du levier releveur de fil, jusqu’à ce que le fil soit derrière le

levier releveur de fil. Guider le fil vers la gauche en l’amenant con-

tre le levier releveur puis continuer vers le bas et vers l’aiguille à

travers la fente gauche. Ceci devrait automatiquement embobiner

le fil sur le levier releveur. (fig. C)

6. Amener le fil à l’aiguille en le faisant passer derrière le guide-fil

juste au-dessus de l’aiguille. (fig. D)

7. Enfiler l’aiguille de l’avant vers l’arrière en laissant dépasser envi-

ron 5 cm de fil.

REMARQUE :

Si le fil n’est pas correctement mis en place, il pourrait se casser, cer-

tains points ne seront pas faits ou le tissu pourrait froncer.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Brother LS1217 in the language / languages: English, French, Portuguese, Spanish as an attachment in your email.

The manual is 1,32 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Brother LS1217 Manual

Product: