631286
54
Zoom out
Zoom in
Previous page
1/68
Next page
45
Cleaning the Feed Dogs
1. Remove the presser foot holder and the needle.
2. Remove the needle plate using a coin or oval screwdriver to
take out the screws.
3. Clean the lint from the upper part of the feed dogs and shuttle
race body with a brush.
Performance Checklist
Whenever sewing difficulties are encountered, review the section
in this instruction manual that details the operation you are
performing to make sure you are correctly using the machine. If
the problem continues, the following checklist may help you to
improve the operation.
If you still have difficulties, contact your nearest service center.
Nettoyage des griffes d’entraînement
1. Retirer le support de pied-de-biche et l’aiguille.
2. Retirer la plaque à aiguille avec une pièce de monnaie ou un
tournevis en forme de disque pour desserrer les vis.
3. Nettoyer la partie supérieure des griffes d’entraînement et de
la coursière de la navette à l’aide d’une brosse.
Liste de vérification en cas de
défaillances
En cas de problème, consulter d’abord le chapitre voulu dans le
présent manuel pour s’assurer de la bonne utilisation de la
machine. Si le problème persiste, la liste de vérification suivante
peut vous aider à y remédier.
Si vous ne parvenez toujours pas à résoudre le problème, veuillez
contacter le centre technique le plus proche.
Limpieza de los alimentadores
1. Quite el soporte del prensatelas y la aguja.
2. Retire la placa de agujas con una moneda o el destornillador de
cabeza ovalada para aflojar los tornillos.
3. Limpie la parte superior de los dientes y el cuerpo de la lanzadera
con un cepillo.
Listado de posibles incidencias
Cada vez que encuentre dificultades al coser, vuelva a consultar la
parte de este manual de instrucciones que detalla la operación que
está realizando, para comprobar que usa correctamente la máquina.
Si el problema persiste, el siguiente listado le puede ayudar a mejorar
el funcionamiento.
Si a pesar de eso el problema persiste, póngase en contacto con el
servicio técnico más cercano.
Очистка гребенок транспортера
1. Снимите адаптер прижимной лапки и иглу.
2. Снимите игольную пластину, используя монету или
овальную отвёртку для выворачивания винтов.
3. Очистите щеточкой верхнюю часть гребенок транспортера
и обоймы челнока.
Таблица контрольных проверок
технических характеристик
При возникновении каких-либо трудностей при шитье,
сначала просмотрите раздел руководства, касающийся
выполняемой операции, чтобы убедиться, что вы правильно
используете машину. Если проблема остается, приведенная
ниже таблица контрольных проверок может помочь устранить
неисправность.
Если неисправность устранить самостоятельно не удается,
обратитесь в ближайший сервисный центр.
54


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother LS-3125 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother LS-3125 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 9,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info