718836
64
Zoom out
Zoom in
Previous page
1/72
Next page
62
APPENDIX
p
Insert the bobbin case by following step g in
“Cleaning the race” (page 58).
q
Attach the needle plate cover according to steps
h and i in “Cleaning the race” (page 58).
r
Check the condition of the needle, and then
install it.
Refer to “Checking the needle” (page 19) and
“Replacing the needle” (page 20).
Note
After completing this procedure, continue with the
following procedure in “Checking machine
operations” to check that the machine is operating
correctly.
Memo
Since the needle may have been damaged when
the fabric was caught in the machine, we
recommend replacing it with a new one.
Checking machine operations
If the needle plate has been removed, check
machine operations to confirm that installation has
been completed correctly.
a
Turn on the machine.
b
Select (middle needle position stitch).
Note
Do not yet install the presser foot and thread.
c
Slowly turn the handwheel toward you
(counterclockwise), and look from all sides to
check that the needle falls at the center of the
hole in the needle plate.
If the needle contacts the needle plate, remove
the needle plate, and then install it again, starting
with step
m in “Removing the fabric from the
machine” (page 61).
a Hole in the needle plate
b Handwheel
d
Select zigzag stitch . At this time, increase the
stitch length and width to their maximum settings.
Refer to “Adjusting the stitch length and width”
(page 24).
e
Slowly turn the handwheel toward you
(counterclockwise) and check that the needle
bar and feed dogs operate correctly.
If the needle or feed dogs contact the needle plate,
the machine may be malfunctioning; therefore,
contact your nearest authorized service center.
f
Turn off the machine, and then install the
bobbin and presser foot.
Refer to “Lower threading” (page 13) and
“Replacing the presser foot” (page 22).
g
Correctly thread the machine.
Refer to “Upper threading” (page 15).
Note
The thread may have become tangled as a result of
incorrect upper threading. Make sure that the
machine is correctly threaded.
h
Perform trial sewing with normal fabric.
Note
Incorrect sewing may be the result of incorrect upper
threading or sewing thin fabrics. If there are poor results
from the trial sewing, check the upper threading or the
type of fabric being used.
CAUTION
Never use bent needles. Bent needles can easily
break, possibly resulting in injuries.
64


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother KE20 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother KE20 in the language / languages: English as an attachment in your email.

The manual is 2,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother KE20

Brother KE20 User Manual - German - 72 pages

Brother KE20 User Manual - Dutch - 72 pages

Brother KE20 User Manual - French - 72 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info