Manual Brother JS-23 (page 42 of 66) (German, Dutch, French, Italian)

631250

Zoom out

Zoom in

1/66

Knöpfe annähen

Stichart Fuß Sonstiges

2, 3 oder 4 Knopfannähfuß Stopfplatte

1. Messen Sie den Abstand zwischen den Löchern des Knopfes,

und stellen Sie den Musterwähler auf den Zickzackstich (2, 3

oder 4) mit der dazu passenden Breite.

Lochabstand Muster

1,6mm 2

3,2 mm 3

4,8 mm 4

2. Montieren Sie den Knopfannähfuß.

3. Plazieren Sie die Stopfplatte auf der Stichplatte, wie in Abb. A

gezeigt.

4. Legen Sie einen Knopf zwischen Fuß und Stoff, drehen Sie das

Handrad, und stellen Sie sicher, daß die Nadel ohne anzustreifen

in die Befestigungslöcher einsticht. Wenn dies passiert, beach-

ten Sie Schritt 1.

5. Nähen Sie mit langsamer Geschwindigkeit etwa 10 Stiche.

6. Nehmen Sie das Material aus der Maschine. Schneiden Sie

Ober- und Unterfaden; lassen Sie dabei 15 cm stehen. Ziehen

Sie den Oberfaden mit einer Nähnadel nach innen, und ver-

knoten Sie beide Fäden an der Stoffunterseite.

Pour coudre un bouton

Modèle Pied-de-biche Autre

2, 3 ou 4 Pied pour boutons Plaque à repriser

1. Mesurer la distance entre les orifices et régler le sélecteur de

modèle de point sur le point zigzag (2,3 ou 4) ayant la largeur

appropriée.

Distance entre les orifices Modèle

1,6 mm 2

3,2 mm 3

4,8 mm 4

2. Fixer le pied pour boutons.

3. Placer la plaque à repriser sur la plaque à aiguille comme le

montre la fig. A.

4. Placer un bouton entre le pied et le tissu, tourner le volant et

veiller à ce que l’aiguille pique dans les trous sans heurter le

bouton. Si jamais elle heurte le bouton, veuillez vous reporter

au point 1.

5. Coudre environ 10 points à faible vitesse.

6. Retirer le tissu de la machine. Couper les fils inférieur et supé-

rieur en laissant à chacun une longueur de 15 cm. Utiliser une

aiguille à coudre normale pour faire passer le fil supérieur à

l’envers du tissu. Nouer les deux fils pour éviter que la couture

ne se défasse.

Knopen aanzetten

Patroon Voet Div.

2, 3 of 4 Knoopaanzetvoet Stopplaatje

1. Meet de afstand tussen de knoopsgaten en stel de patroonkeuze-

knop in op de Zigzagsteek (2, 3 of 4) met de gewenste breedte.

Afstand tussen de gaten Patroon

1,6 mm 2

3,2 mm 3

4,8 mm 4

2. Monteer de knoopsgatvoet.

3. Leg het stopplaatje op de naaldplaat zoals ge-toond in fig. A.

4. Leg de knoop tussen de voet en de stof, draai aan het handwiel en

zorg ervoor dat de naald precies door de gaatjes gaat zonder de

knoop te raken. Lukt dit niet, raadpleeg dan stap 1.

5. Naai langzaam en voorzichtig ongeveer 10 steken.

6. Haal het materiaal van de naaimachine af. Knip de boven- en onder-

draad door waarbij u ongeveer 15 cm lengte laat. Gebruik een ge-

wone naainaald om met de hand de bovendraad naar de achterkant

van het materiaal te trekken. Knoop de twee draadjes aan elkaar

vast om het vast te zetten.

Cucitura di bottoni

Punto Piedino Altri accessori

2, 3 o 4 prescelti per bottoni Placca da rammendo

Misurare la distanza fra i fori del bottone ed impostare il selettore dei

punti sul Punto ZigZag (N. 2, 3 o 4) regolando l’ampiezza desiderata.

Distanza tra i fori Punto

1,6 mm 2

3,2 mm 3

4,8 mm 4

2. Applicare il piedino per i bottoni.

3. Applicare la placca da rammendo sulla placca dell’ago come mo-

strato in fig. A.

4. Inserire il bottone fra il piedino e il tessuto, far girare il volantino,

accertandosi che l’ago entri nei fori senza colpire il bottone. Altri-

menti ripetere il punto 1.

5. Eseguire circa 10 punti a bassa velocità.

6. Estrarre il tessuto dalla macchina. Tagliare il filo superiore e infe-

riore lasciando una lunghezza di 15 cm. Utilizzare un ago per cuci-

tura manuale per fissare il filo superiore al rovescio del tessuto.

Legare i due fili assieme per fissarli.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Brother JS-23 in the language / languages: German, Dutch, French, Italian as an attachment in your email.

The manual is 0,79 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother JS-23

Brother JS-23 User Manual - English, French, Portuguese, Spanish - 67 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Brother JS-23 Manual

Product: