631249
51
Zoom out
Zoom in
Previous page
1/84
Next page
40
BUTTONHOLE AND BUTTON SEWING
NAPINLÄPIEN JA NAPPIEN OMPELEMINEN
OJALES Y COSTURA DE BOTONES
ОБМЕТЫВАНИЕ ПЕТЕЛЬ И ПРИШИВАНИЕ ПУГОВИЦ
Button Sewing
STITCH LENGTH 0
STITCH WIDTH Set according to the distance between the
holes.
NEEDLE POSITION L or R
PRESSER FOOT Zigzag
NEEDLE Single
OTHER Darning Plate
1. Set the darning plate on the needle plate over the feed dogs as
shown in the illustration and press down into place.
2. Place a button between the presser foot and the fabric.
3. You will need to adjust the stitch width to match the distance be-
tween the holes in the button. Turning the width knob will narrow
or widen the "swing" of the stitch to accommodate most buttons.
4. To check the width, move the balance wheel toward you while
observing the needle. Turn several times to make sure the needle
goes easily into the both holes on the button without touching the
button.
5. Slowly sew about 10 stitches.
6. Stop the machine and raise the needle from the fabric.
7. Remove the fabric from the machine and cut the upper and lower
threads leaving at least 10 cm (4"). With a normal sewing needle,
pull the threads to the back of the fabric and tie them together to
secure the button.
8. Remove the darning plate for normal sewing by pulling up on the
front edge.
1 Front edge slot on darning plate
Button Fitting with Thread Shank
The thread shank of a button is often needed when sewing on heavier
fabric.
1. Place a button between the presser foot and the fabric, adjust the
stitch width according to the distance between the holes in the
button and sew on the button as previously explained.
2. After sewing about 10 stitches, remove the fabric from the machine
leaving a longer upper thread (about 15 cm (6")) in order to form a
thread shank.
3. Pull the upper thread through one of the holes on the button until it
is between the button and the fabric and tightly wrap the thread
around the stitches.
4. With a normal sewing needle, pull the threads to the back of the
fabric and tie the ends together to secure the button.
Napin ompeleminen
PISTON PITUUS 0
PISTON LEVEYS Aseta reikien etäisyyden mukaan.
NEULA-ASENTO L tai R
PAININJALKA Siksak
NEULA Tavallinen neula
MUUTA Syöttäjän peitelevy
1. Aseta syöttäjän peitelevy pistolevyn ja syöttäjän hampaiden päälle
kuvan mukaisesti ja paina se paikalleen.
2. Aseta nappi paininjalan ja kankaan väliin.
3. Joudut säätämään piston leveyttä, jotta se vastaa napin reikien vä-
listä etäisyyttä. Nupin kääntäminen kaventaa tai leventää piston
liikettä, jolloin se saadaan sopivaksi useimmille napeille.
4. Tarkasta leveys kääntämällä käsipyörää itseäsi kohden pitämällä
samalla silmällä neulaa. Käännä sitä useita kertoja varmistaen, että
neula kulkee molemman reiän läpi koskettamatta nappia.
5. Ompele hitaasti noin 10 pistoa.
6. Pysäytä kone ja nosta neula kankaasta.
7. Poista kangas koneesta ja katkaise ylä- ja alalanka jättäen ainakin
10 cm:n (4 tuuman) langanpäät. Vedä langanpäät kankaan nurjalle
puolelle tavallisella ompeluneulalla ja solmi ne kiinnittääksesi na-
pin lujasti paikalleen.
8. Irrota syöttäjän peitelevy, jotta koneella voi taas ommella normaa-
listi, nostamalla sitä sen etureunasta.
1
Syöttäjän peitelevyn etureuna
Kaulan ompeleminen nappiin
Kaula on joskus tarpeen ommeltaessa nappia paksuun kankaaseen.
1. Aseta nappi paininjalan ja kankaan väliin, säädä piston leveyttä,
jotta se vastaa napin reikien välistä etäisyyttä, ja ompele nappi edel-
listen ohjeiden mukaan.
2. Poista kangas koneesta noin 10 piston jälkeen ja jätä noin 15 cm:n
(6 tuuman) pituinen ylälanganpää, jolla kaula muodostetaan.
3. Vie ylälanka napin toisen reiän läpi, kunnes se on napin ja kan-
kaan välissä, ja kierrä lanka tiukasti pistojen ympärille.
4. Vedä langanpäät kankaan nurjalle puolelle tavallisella
ompeluneulalla ja solmi ne kiinnittääksesi napin lujasti paikalleen.
08C713_XE4683-001_P36-41 2008.04.02, 09:3240
51


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother JS-20 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother JS-20 in the language / languages: English, Spanish as an attachment in your email.

The manual is 1,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info