631248
111
Zoom out
Zoom in
Previous page
1/116
Next page
109
4
The thread does
not pass through
the eye of the
needle.
The needle was not raised.
Press (needle position button)
once or twice to raise the needle.
page 21
The needle is incorrectly installed. Correctly install the needle. page 31
The stitch is not
sewn correctly.
The appropriate presser foot for the
type of stitch that you wish to sew is
not used.
Attach the presser foot that is
appropriate for the type of stitch that
you wish to sew.
page 89
The thread tension is incorrectly set. Adjust the thread tension. page 49
The thread is tangled, for example, in
the bobbin case.
Remove the tangled thread. If the
thread is tangled in the bobbin case,
clean the race.
page 95
The fabric does
not feed.
The feed dogs are lowered.
Slide the feed dog position switch to
.
page 75
The stitch is too short. Lengthen the stitch length. page 42
The combination of fabric, thread and
needle is incorrect.
Select a thread and needle that are
appropriate for the type of fabric
being sewn.
page 30
The thread is tangled, for example, in
the bobbin case.
Remove the tangled thread. If the
thread is tangled in the bobbin case,
clean the race.
page 95
Zigzag foot “J” is slanted on a thick
seam at the beginning of stitching.
Use the presser foot locking pin
(black button on the left side) on
zigzag foot “J” to keep the presser
foot level while sewing.
page 51
The sewing lamp
does not come
on.
The sewing lamp is damaged.
Contact your dealer or the nearest
authorized service center.
While winding
the bobbin, the
bobbin thread
was wound
below the bobbin
winder seat.
You have not wound the bobbin thread
properly.
After removing the thread wound below
the bobbin winder seat, wind the
bobbin correctly.
page 104
Bobbin thread
does not wind
neatly on the
bobbin.
The thread is not passed through the
bobbin-winding thread guide correctly.
Correctly pass the thread through the
bobbin-winding thread guide.
page 15
Bobbin spins slowly.
Move the sewing speed controller to the
right (so that the speed will be fast).
page 17
The thread that was pulled out was not
wound onto the bobbin correctly.
Wind the thread that was pulled off
round the bobbin five or six times
clockwise.
page 17
Fabric being
sewn with the
machine cannot
be removed.
Thread is tangled below the needle
plate.
Lift up the fabric and cut the threads
below it, and clean the race.
page 101
The fabric feeds
in the opposite
direction.
The feed mechanism is damaged.
Contact your dealer or the nearest
authorized service center.
The upper thread
has tightened up.
The bobbin thread is incorrectly
installed.
Correctly install the bobbin thread. page 18 , 97
The thread is
tangled on the
wrong side of the
fabric.
You have not threaded the upper thread
properly.
Correct the upper threading. page 20 , 98
Symptom Probable Cause Remedy Reference
111


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother JK7000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother JK7000 in the language / languages: English as an attachment in your email.

The manual is 3,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info