631248
57
Zoom out
Zoom in
Previous page
1/116
Next page
55
3
Basic Stitching
Straight stitches are used for sewing plain seams. Three stitches are available for basic stitching.
Pattern numbers vary depending on the machine model. Check the pattern numbers available with your
machine, and select the desired stitch.
The values below “Auto” are set when the pattern is selected. The setting can be adjusted to any value within the range
indicated below “Manual”.
a
Baste or pin together the fabric pieces.
b
Turn on the machine.
c
With the pattern selection dial,
select , or .
d
Attach zigzag foot “J”.
For details, refer to “Replacing the presser
foot” (page 33).
e
If reverse stitches are to be sewn, lower the
needle into the fabric 3 to 5 stitch lengths in
front of the point where the stitching will
begin, and then sew the reverse stitches.
For details, refer to “Securing the stitching”
(page 46).
f
Start sewing.
For details, refer to “Starting to sew”
(page 44).
g
If reverse stitches are to be sewn at the end of
stitching, sew 3 to 5 reverse stitches.
For details, refer to “Securing the stitching”
(page 46).
h
When sewing is finished, cut the thread.
Changing the needle position
The needle position can be adjusted with the
straight stitch (left needle position) and the triple
stretch stitch by adjusting the stitch width. Press
the “–” side of the stitch width key for a left
needle position, or press the “+” side for a right
needle position.
a Stitch width
b Stitch width key
c Moves the needle position to the left
d Moves the needle position to the right
Stitch Name
Pattern
Presser Foot
Pattern No.
Application
Stitch Width
[mm (inch)]
Stitch Length
[mm (inch)]
Twin Needle
Walking Foot
Reverse/
Reinforcement
Stitching
70 stitches
model
60 stitches
model
50 stitches
model
40 stitches
model
Auto Manual Auto Manual
Straight stitch
Left
J01010101
Basic stitching, sew-
ing gathers or pin-
tucks, etc.
0.0
(0)
0.0–7.0
(0–1/4)
2.5
(3/32)
0.2–5.0
(1/64–3/16)
Yes
(J) Yes
Reverse
Cen-
ter
J02020202
Attaching zippers,
basic stitching, and
sewing gathers or
pintucks, etc.
3.5
(1/8)
0.0–7.0
(0–1/4)
2.5
(3/32)
0.2–5.0
(1/64–3/16)
Yes
(J) Yes
Reverse
Triple stretch
stitch
J03030303
Attaching sleeves,
sewing inseams, sew-
ing stretch fabrics
and decorative stitch-
ing
0.0
(0)
0.0–7.0
(0–1/4)
2.5
(3/32)
1.5–4.0
(1/16–3/16)
Yes
(J)
No
Reinforcement
*
1
Do not use reverse stitching.
Before replacing the presser foot, be sure to turn off the sewing machine, otherwise injuries may occur if
a button is accidentally pressed and the machine starts sewing.
*
1
*
1
CAUTION
dc
ab
57


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother JK7000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother JK7000 in the language / languages: English as an attachment in your email.

The manual is 3,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info